Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ENAC*DENVIRONMENTAL ATTRIBUTE CODE

INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.

Enter the applicable reply code from the table below

(ENACDG4)

Table 1
	Reply Code (EN02)	Reply
	G4	COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

MATT*DMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(MATT3AATDCUB000*;MATT3AATDCUB000$DFEA000*;MATT3AATDCUB000$$DFEA000*)

Table 1
	ISAC Field Indicator (5000)	Location
	3AAT	BODY
	3AEE	OVERALL
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (MA01)	Reply
	ALA000	ALUMINUM
	ALB000	ALUMINUM ALLOY
	CUB000	COPPER ALLOY
	FEA000	IRON
	FEB000	IRON CAST
	STA000	STEEL
	ZNB000	ZINC
	ZND000	ZINC,DIE CAST (POT METAL)

AFJE*GSPECIFIC EQUIPMENT ACCOMMODATED

THE NAME OF THE EQUIPMENT THE ITEM IS SPECIFICALLY DESIGNED TO ACCOMMODATE.

Enter clear text.

(AFJEGCLEARTEXT)

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

This MRC replaced MRC ZZZP

The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.

PDNB*APURCHASE DESCRIPTION IDENTIFICATION

THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.

Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.

(ZZZPJ81A37-30624A*)

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

HZRD*DHAZARDOUS SUBSTANCES

THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.

Enter the applicable reply code from the table below

(HZRDDHAZ222*;HZRDDHAZ012$$DHAZ052*)

Table 1
	Reply Code (HZ00)	Reply
	HAZ012	COPPER
	HAZ222	IRON
	HAZ029	LEAD
	HAZ052	ZINC

CQRGDBODY MATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BODY IS FABRICATED.

Enter the applicable reply code from the table below

(CQRGDMGB000*;CQRGDALB000$DALA000*;CQRGDALB000$$DALA000*)

Table 1
	Reply Code (MA01)	Reply
	ALA000	ALUMINUM
	ALB000	ALUMINUM ALLOY
	CUB000	COPPER ALLOY
	FEB000	IRON CAST
	MGA000	MAGNESIUM
	MGB000	MAGNESIUM ALLOY
	STA000	STEEL
	ZNA000	ZINC ALLOY

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)