Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAI1379	A1	ARMATURE MOTOR
AAI1388	A10	ARMATURE MOTOR
AAI1389	A11	ARMATURE MOTOR-GENERATOR
AAI1390	A12	ARMATURE MOTOR-GENERATOR
AAI1391	A13	ARMATURE DYNAMOTOR
AAI1392	A14	ARMATURE GENERATOR
AAI1393	A15	ARMATURE MOTOR
AAI1394	A16	ARMATURE GENERATOR
AAI1395	A17	ARMATURE GENERATOR
AAI1396	A18	ARMATURE GENERATOR
AAI1380	A2	ARMATURE MOTOR-GENERATOR
AAI1397	A20	ARMATURE DYNAMOTOR
AAI1381	A3	ARMATURE MOTOR
AAI1382	A4	ARMATURE MOTOR
AAI1383	A5	ARMATURE MOTOR
AAI1384	A6	ARMATURE MOTOR
AAI1385	A7	ARMATURE MOTOR
AAI1386	A8	ARMATURE MOTOR
AAI1387	A9	ARMATURE MOTOR

ACDC*DCURRENT TYPE

INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.

Enter the applicable reply code from the table below

(ACDCDC)

Table 1
	Reply Code (AB62)	Reply
	B	AC
	D	AC/DC
	C	DC

ABHPJOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAVJOVERALL DIAMETER

A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) CMT WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (BYDT)

IF STYLE/REPLY CODE(s) CVH WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (FEAT)

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDFNY*;CBBLDCVJ$$DCMT*)

Table 1
	Reply Code (AN47)	Reply
	CMT	BEARING
	ARF	BRAKE SHOE
	CVH	REPLACEABLE FAN
	FNY	ROHS DIRECTIVE COMPLIANCE
	CVJ	SHAFT

BYDT*DBEARING TYPE

INDICATES THE TYPE OF BEARING PROVIDED.

Enter the applicable reply code from the table below

(BYDTDBH)

Table 1
	Reply Code (AH96)	Reply
	BH	BUSHING
	AJ	ROLLER
	AK	SLEEVE
	BA	THRUST

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

AARG*DRELIABILITY INDICATOR

AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.

Enter the applicable reply code from the table below

(AARGDE)

Table 1
	Reply Code (AA61)	Reply
	E	ESTABLISHED
	N	NOT ESTABLISHED

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	CS	CONSTRUCTION
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	FN	FINISH
	FM	FORM
	FA	FORMULA
	GR	GRADE
	GP	GROUP
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LT	LIMIT
	MK	MARK
	AA	MARKER
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	NR	NUMBER
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	QA	QUALITY
	RN	RANGE
	RT	RATING
	RF	REFERENCE NUMBER
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH