An item consisting of insulating material, which is specifically designed to have fastened thereon, or on which are fastened terminal(s), such as screws, solder lugs, solder studs, solderless connectors, clips, and the like. It is usually used for junctions or terminations of wire or cable assemblies. It does not include items as defined above with parts, such as resistors and capacitors mounted thereon. Do not use if a more specific name exists, such as FUSEHOLDER; HOLDER, RESISTOR; FANNING STRIP; CONTACT ASSEMBLY, ELECTRICAL; JACK ASSEMBLY, TIP; CHAMBER, CABLE TERMINAL; PANEL (2) (as modified); CONNECTOR (as modified). Excludes:TERMINAL, STUD; TERMINAL, FEEDTHRU, INSULATED; POST, BINDING, ELECTRICAL; and CHASSIS, ELECTRICAL-ELECTRONIC EQUIPMENT. For items having printed electrical conductor paths, see PRINTED WIRING BOARD.
expandFSC Information
5940Lugs, Terminals, and Terminal Strips
expandColloquial Information
I0506HEADER,ELECTRICAL-ELECTRONIC COMPONENTS
K0093TERMINAL BLOCK ASSEMBLY,RECTIFIER SET
J4864BLOCK,BINDING POST
K0095ELECTRIC MOLDED-IN-STUD TERMINAL BOARD ASSEMBLY
G4593BASE PLATE,VOLTAGE ASSEMBLY
J4898BOARD,TERMINAL
K0096TERMINAL,ELECTRICAL,STANDOFF
K0091FEED THROUGH TERMINAL
K0092MICRO TERMINAL STRIP
K0094TERMINAL BOARD ASSEMBLY,MOLDED-IN-STUD,ELECTRIC
J5083MOUNTING,TERMINAL
expandChange List
ISAC Reply 3AEE added to MRC CRNL.
ISAC Reply 3EDU added to MRC CRNL.
ISAC Reply 3HOU added to MRC CRNL.
ISAC Reply 3AEE added to MRC CSCS.
ISAC Reply 3EDU added to MRC CSCS.
ISAC Reply 3HOU added to MRC CSCS.
ISAC Reply 3AEE added to MRC CQCW.
ISAC Reply 3EDU added to MRC CQCW.
ISAC Reply 3EHD added to MRC CQCW.
ISAC Reply 3HOU added to MRC CQCW.
ISAC Reply 3AEE added to MRC CRZR.
ISAC Reply 3EDU added to MRC CRZR.
ISAC Reply 3HOU added to MRC CRZR.
ISAC Reply 3AEE added to MRC CQCZ.
ISAC Reply 3EDU added to MRC CQCZ.
ISAC Reply 3HOU added to MRC CQCZ.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00404*)
IF STYLE/REPLY CODE(s) A1, A2, A3, A4, A5, A6, A7, A14 OR A18 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGQ and ABGP and ABGN and ABGS and ABGR and CWLG)
IF STYLE/REPLY CODE(s) A8 OR A20 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGP and ABGQ and ABGS and ABGN and CWLG)
IF STYLE/REPLY CODE(s) A9 OR A12 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGP and ABGT and ABGN and CWLG)
IF STYLE/REPLY CODE(s) A15, A17, A35 OR A36 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGQ and ABGP and ABGN and CWLG)
IF STYLE/REPLY CODE(s) A10 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGT and ABGN and ABGP and CWLG)
IF STYLE/REPLY CODE(s) A11 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGT and ABGN and ABGP and ABGQ and CWLG)
IF STYLE/REPLY CODE(s) A16 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGQ and ABGN and ABGP and ABGR and CWLG and ABGS)
IF STYLE/REPLY CODE(s) A22 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGR and ABGN and ABGT and ABGQ)
IF STYLE/REPLY CODE(s) A26, A27 OR A28 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGR and ABGN and ABGT and ABGQ and CRTC)
IF STYLE/REPLY CODE(s) A29 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (CWLJ and ABGR and CWLG)
IF STYLE/REPLY CODE(s) A31 OR A32 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (CWLL and ABGR and CWLJ and CWLG)
IF STYLE/REPLY CODE(s) A34 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGP and ABGR and CWLJ and CWLG)
IF STYLE/REPLY CODE(s) A41A OR A41B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGP)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLLA41A)
Table 1
Physical Drawing IDReply Code (STYL)Reply
AAR1184A1BARRIER TYPE
AAR1193A10BLOCK TYPE
AAR1194A11STANDOFF
AAR1195A12BLOCK TYPE
AAR1196A14BARRIER STANDOFF
AAR1197A15PRESSURE-CONTACT-RIGID
AAR1198A16PRESSURE-CONTACT-FLEXIBLE
AAR1199A17TAPER PIN
AAR1200A18L-SHAPE
AAR1185A2BARRIER TYPE
AAR1201A20T-SHAPE
AAR1202A22STRIP
AAR1203A26STRIP
AAR1204A27STRIP
AAR1205A28STRIP
AAR1206A29CIRCULAR
AAR1186A3BARRIER TYPE
AAR1207A31CIRCULAR STEPPED
AAR1208A32CIRCULAR TAPERED
AAR1209A34SEMI-CIRCULAR
AAR1210A35SECTIONAL
AAR1211A36SECTIONAL
AAR1187A4BARRIER TYPE
DR01913A41ACURVED W/BARRIERS
DR01914A41BCURVED W/O BARRIERS
AAR1188A5BARRIER TYPE
AAR1189A6BARRIER TYPE
AAR1190A7BARRIER TYPE
AAR1191A8STANDOFF
AAR1192A9STRIP TYPE
IF STYLE/REPLY CODE(s) G WERE ENTERED FOR MRC ABCX, YOU MUST ANSWER MRC (BWGP and ABCZ) or (BWGP and ABDA)
ABCXDBOARD CONSTRUCTION
THE STRUCTURAL CHARACTERISTIC(S) OF THE BOARD.
Enter the applicable reply code from the table below
(ABCXDF*;ABCXDH$DG*)
Table 1
Reply Code (AB20)Reply
KCOMPRESSION SEAL CONSTRUCTION
HCONSTRUCTED FOR STACKING IDENTICAL BOARDS
FCONSTRUCTED OF INDIVIDUAL PIECES WHICH ARE MOUNTED ON A TRACK OR CHANNEL
ECONSTRUCTED OF INTERLOCKING PIECES
BHOLLOW CONSTRUCTION WITH INSULATED STRIP
CHOLLOW CONSTRUCTION WITH MARKED INSULATED STRIP
DHOLLOW CONSTRUCTION WITHOUT INSULATED STRIP
GSCORED FOR EASY BREAKING INTO SMALLER TERMINAL BOARDS
ASOLID CONSTRUCTION
JTWO PIECE BOARD
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AAMA)
IF STYLE/REPLY CODE(s) BNK OR BXN WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AAMB)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AAQX and AAQW)
IF STYLE/REPLY CODE(s) ACH, AET, AHF OR BXP WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (CDTD)
AXHRJMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJAEC2*;AXHRJAEC2$$JAEC3*)
Table 1
Reply Code (AM39)Reply
BNFANCHOR NUTS
ABCBRACKET
ABDBUSHING
ABGCEMENT
BNGCHANNEL
ABHCLAMP
AECCLINCH NUT
AFLCLIP
BHYFEET
ACRFLANGE
ADTFLAT BASE
ABLFRICTION
BNKHEX HOLES
AGCHINGE
BGYLAP RIVETED
ABPPLUG-IN
BKYRAIL
ABYSLOT
AHASOLDER
BXNSQUARE HOLES
ACDTERMINAL
AHFTHREADED HOLE
ACHTHREADED INSERT
BXPTHREADED NUT
AETTHREADED STUD
ACQUNTHREADED HOLE
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDST1145*;MATT3AEEDST1145$DST0431*;MATT3AEEDST1145$$DST0431*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3EDVTERMINALS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (MA01)Reply
ALA000ALUMINUM
ALB000ALUMINUM ALLOY
AL1100ALUMINUM ALLOY 1100
AL2011ALUMINUM ALLOY 2011
AL2024ALUMINUM ALLOY 2024
AL5052ALUMINUM ALLOY 5052
AL6061ALUMINUM ALLOY 6061
AL6062ALUMINUM ALLOY 6062
AL6063ALUMINUM ALLOY 6063
AL7075ALUMINUM ALLOY 7075
AL0262ALUMINUM ALLOY A-G3
AL0193ALUMINUM ALLOY A-G3T
ASA000ASBESTOS
GFB000BAKELITE-GRAPHITE
BEA000BERYLLIUM
BEB000BERYLLIUM COPPER (USE CUB000)
BEC000BERYLLIUM OXIDE
CSA000CELLULOSE
CLD000CERAMIC
CLF000CERAMIC ALUMINA (USE ALUMINUM OXIDE)
CRA000CHROMIUM
CTA000COBALT
CUA000COPPER
CUB000COPPER ALLOY
CU0249COPPER ALLOY 102
CU0287COPPER ALLOY 105
CU0063COPPER ALLOY 110
CU0290COPPER ALLOY 114
CU0291COPPER ALLOY 116
CU0248COPPER ALLOY 122
CU0278COPPER ALLOY 125
CU0279COPPER ALLOY 142
CU0068COPPER ALLOY 170
CU0069COPPER ALLOY 172
CU0233COPPER ALLOY 173
CU0263COPPER ALLOY 210
CU0264COPPER ALLOY 220
CU0074COPPER ALLOY 230
CU0076COPPER ALLOY 240
CU0079COPPER ALLOY 260
CU0304COPPER ALLOY 262
CU0080COPPER ALLOY 268
CU0081COPPER ALLOY 270
CU0272COPPER ALLOY 272
CU0274COPPER ALLOY 274
CU0302COPPER ALLOY 280
CU0314COPPER ALLOY 314
CU0316COPPER ALLOY 316
CU0320COPPER ALLOY 320
CU0330COPPER ALLOY 330
CU0305COPPER ALLOY 331
CU0332COPPER ALLOY 332
CU0335COPPER ALLOY 335
CU0340COPPER ALLOY 340
CU0088COPPER ALLOY 342
CU0306COPPER ALLOY 344
CU0307COPPER ALLOY 345
CU0308COPPER ALLOY 347
CU0309COPPER ALLOY 348
CU0310COPPER ALLOY 350
CU0089COPPER ALLOY 353
CU0090COPPER ALLOY 356
CU0091COPPER ALLOY 360
CU0370COPPER ALLOY 370
CU0092COPPER ALLOY 377
CU0098COPPER ALLOY 462
CU0099COPPER ALLOY 464
CU0465COPPER ALLOY 465
CU0466COPPER ALLOY 466
CU0467COPPER ALLOY 467
CU0100COPPER ALLOY 482
CU0101COPPER ALLOY 485
CU0103COPPER ALLOY 510
CU0104COPPER ALLOY 511
CU0106COPPER ALLOY 524
CU0109COPPER ALLOY 544
CU0131COPPER ALLOY 655
CU0670COPPER ALLOY 670
CU0675COPPER ALLOY 675
CU0148COPPER ALLOY 745
CU0150COPPER ALLOY 752
CU0757COPPER ALLOY 757
CU0152COPPER ALLOY 764
CU0157COPPER ALLOY 770
CU0175COPPER ALLOY 844
CCA000COTTON
FBA000FIBER
WDA000FIBERBOARD
FBT000FLAX
GSA000GLASS
GSB000GLASS FIBER
GSM000GLASS WIRED
AUA000GOLD
AUB000GOLD ALLOY
FEA000IRON
FBK000JUTE
PBA000LEAD
LRE000LEATHER ARTIFICIAL
MGB000MAGNESIUM ALLOY
AYA000MICA
AYB000MICA GLASS BONDED
NLA000NICKEL
NLB000NICKEL ALLOY
FBB000NYLON
XXA000OXIDE
XXF000OXIDE ALUMINUM
PPA000PAPER
PCA000PLASTIC
PCB000PLASTIC ACETAL
PCD000PLASTIC ACRYLIC
PCE000PLASTIC ALKYD
PCAAM0PLASTIC AMINO
PCAN00PLASTIC CELLULOSE ACETATE
PCBN00PLASTIC CELLULOSE ACETATE BUTYRATE
PCBJ00PLASTIC CELLULOSE NITRATE
PCAAN0PLASTIC CELLULOSE PROPIONATE
PCAAP0PLASTIC CHLORINATED POLYETHER
PCAAQ0PLASTIC CHLOROTRIFLUOROETHYLENE
PCG000PLASTIC DIALLYL PHTHALATE
PCH000PLASTIC EPOXY
PCBY00PLASTIC ETHYL CELLULOSE
PCAAD0PLASTIC FLUOROCARBON
PCAAR0PLASTIC FURANE
PCJ000PLASTIC MELAMINE
PCBB00PLASTIC METHACRYLATE
PCK000PLASTIC METHYL METHACRYLATE
PCM000PLASTIC PHENOL-FORMALDEHYDE
PCN000PLASTIC PHENOLIC
PCBK00PLASTIC PHENOXY
PCP000PLASTIC POLYAMIDE (NYLON)
PCQ000PLASTIC POLYCAPROLACTAM
PCR000PLASTIC POLYCARBONATE
PCW000PLASTIC POLYESTER
PCBS00PLASTIC POLYETHER
PCX000PLASTIC POLYETHYLENE
PCY000PLASTIC POLYETHYLENE TEREPHTHALATE
PCAM00PLASTIC POLYHEXAMETHYLENE AMIDE
PCCH00PLASTIC POLYIMIDE
PCAC00PLASTIC POLYPROPYLENE
PCAD00PLASTIC POLYSTYRENE
PCAE00PLASTIC POLYSULFONE
PCAF00PLASTIC POLYTETRAFLUOROETHYLENE
PCAAABPLASTIC POLYUNDECANOAMIDE
PCAH00PLASTIC POLYURETHANE
PCBM00PLASTIC POLYVINYL ACETATE
PCAAT0PLASTIC POLYVINYL ALCOHOL
PCAJ00PLASTIC POLYVINYL CHLORIDE (PVC)
PCBT00PLASTIC POLYVINYL FLUORIDE
PCAK00PLASTIC SILICONE
PCAAW0PLASTIC STYRENE ACRYLONITRILE
PCAL00PLASTIC UREA
PTA000PLATINUM
CLB000PORCELAIN
RSD000RESIN
RSB000RESIN SILICONE
RCE000RUBBER
RCX000RUBBER ISOBUTYLENE ISOPRENE
RCA000RUBBER NATURAL
RCJ000RUBBER POLYBUTADIENE
RCZ000RUBBER POLYURETHANE
RC0021RUBBER SILICONE CLASS Q
RCB000RUBBER SYNTHETIC
SLD000SILICA
SLC000SILICON
AGA000SILVER
AGF000SILVER ALLOY
SLF000STEATITE
STA000STEEL
ST1006STEEL COMP 1006
ST1008STEEL COMP 1008
ST1009STEEL COMP 1009
ST1010STEEL COMP 1010
ST1011STEEL COMP 1011
ST1012STEEL COMP 1012
ST1015STEEL COMP 1015
ST1016STEEL COMP 1016
ST1017STEEL COMP 1017
ST1018STEEL COMP 1018
ST1019STEEL COMP 1019
ST1020STEEL COMP 1020
ST1021STEEL COMP 1021
ST1022STEEL COMP 1022
ST1023STEEL COMP 1023
ST1025STEEL COMP 1025
ST1026STEEL COMP 1026
ST1027STEEL COMP 1027
ST1029STEEL COMP 1029
ST1030STEEL COMP 1030
ST1031STEEL COMP 1031
ST1033STEEL COMP 1033
ST1035STEEL COMP 1035
ST1037STEEL COMP 1037
ST1038STEEL COMP 1038
ST1039STEEL COMP 1039
ST1040STEEL COMP 1040
ST1042STEEL COMP 1042
ST1043STEEL COMP 1043
ST1045STEEL COMP 1045
ST1046STEEL COMP 1046
ST1049STEEL COMP 1049
ST1050STEEL COMP 1050
ST1053STEEL COMP 1053
ST1055STEEL COMP 1055
ST1060STEEL COMP 1060
ST1065STEEL COMP 1065
ST1070STEEL COMP 1070
ST1074STEEL COMP 1074
ST1075STEEL COMP 1075
ST1078STEEL COMP 1078
ST1080STEEL COMP 1080
ST1084STEEL COMP 1084
ST1085STEEL COMP 1085
ST1086STEEL COMP 1086
ST1090STEEL COMP 1090
ST1095STEEL COMP 1095
ST1108STEEL COMP 1108
ST1109STEEL COMP 1109
ST1110STEEL COMP 1110
ST1115STEEL COMP 1115
ST1116STEEL COMP 1116
ST1117STEEL COMP 1117
ST1118STEEL COMP 1118
ST1119STEEL COMP 1119
ST1120STEEL COMP 1120
ST1125STEEL COMP 1125
ST1126STEEL COMP 1126
ST1132STEEL COMP 1132
ST1137STEEL COMP 1137
ST1138STEEL COMP 1138
ST1139STEEL COMP 1139
ST1140STEEL COMP 1140
ST1141STEEL COMP 1141
ST1144STEEL COMP 1144
ST1145STEEL COMP 1145
ST1146STEEL COMP 1146
ST1151STEEL COMP 1151
ST1211STEEL COMP 1211
ST1212STEEL COMP 1212
ST1213STEEL COMP 1213
ST1215STEEL COMP 1215
ST0540STEEL COMP 12L11
ST0063STEEL COMP 12L14
ST1524STEEL COMP 1524
ST1527STEEL COMP 1527
ST1536STEEL COMP 1536
ST1541STEEL COMP 1541
ST1548STEEL COMP 1548
ST1551STEEL COMP 1551
ST1552STEEL COMP 1552
ST0202STEEL COMP 202
ST0302STEEL COMP 302
ST0303STEEL COMP 303
ST0079STEEL COMP 303SE
ST0304STEEL COMP 304
ST0080STEEL COMP 304L
ST0305STEEL COMP 305
ST0309STEEL COMP 309
ST0310STEEL COMP 310
ST0082STEEL COMP 316L
ST0317STEEL COMP 317
ST0321STEEL COMP 321
ST0322STEEL COMP 322
ST0324STEEL COMP 324
ST0347STEEL COMP 347
ST0403STEEL COMP 403
ST0405STEEL COMP 405
ST0410STEEL COMP 410
ST0414STEEL COMP 414
ST0416STEEL COMP 416
ST0099STEEL COMP 416SE
ST0420STEEL COMP 420
ST0430STEEL COMP 430
ST0101STEEL COMP 430F
ST0172STEEL COMP 430FSE
ST0431STEEL COMP 431
ST0105STEEL COMP 440A
ST0106STEEL COMP 440B
ST0107STEEL COMP 440C
ST0108STEEL COMP 440F
ST0285STEEL COMP 440FSE
ST0446STEEL COMP 446
ST0633STEEL COMP 633
ST0634STEEL COMP 634
ST8630STEEL COMP 8630
ST8740STEEL COMP 8740
ST0445STEEL COMP B1010
ST0219STEEL COMP M1008
ST0171STEEL COMP M1010
ST0220STEEL COMP M1012
ST0176STEEL COMP M1015
ST0221STEEL COMP M1017
ST0163STEEL COMP M1020
ST0222STEEL COMP M1023
ST0223STEEL COMP M1025
ST0224STEEL COMP M1031
ST0225STEEL COMP M1044
ST0177STEEL COMP MB1006
ST0178STEEL COMP MB1010
STB000STEEL CORROSION RESISTING
SNB000TIN
WDC000WOOD
WDD000WOOD MAPLE
ZNB000ZINC
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3EDVTERMINALS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AP33)Reply
QAEROSPACE MATERIAL SPEC STD
JAMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP18)Reply
M10TH MATERIAL RESPONSE
N11TH MATERIAL RESPONSE
P12TH MATERIAL RESPONSE
Q13TH MATERIAL RESPONSE
R14TH MATERIAL RESPONSE
S15TH MATERIAL RESPONSE
T16TH MATERIAL RESPONSE
U17TH MATERIAL RESPONSE
W18TH MATERIAL RESPONSE
X19TH MATERIAL RESPONSE
B1ST MATERIAL RESPONSE
Y20TH MATERIAL RESPONSE
Z21ST MATERIAL RESPONSE
V22ND MATERIAL RESPONSE
C2ND MATERIAL RESPONSE
D3RD MATERIAL RESPONSE
E4TH MATERIAL RESPONSE
F5TH MATERIAL RESPONSE
H6TH MATERIAL RESPONSE
J7TH MATERIAL RESPONSE
K8TH MATERIAL RESPONSE
L9TH MATERIAL RESPONSE
GALL MATERIAL RESPONSES
ASINGLE MATERIAL RESPONSE
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDPNA000*;SFTT3AEEDPNA000$DAUA000*;SFTT3AEEDPNA000$$DAUA000*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3EDVTERMINALS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (SF01)Reply
ALB000ALUMINUM
ANA000ANODIZE
CDA000CADMIUM
CDB000CADMIUM ALLOY
CLB000CERAMIC
CMA000CHROMATE
CRA000CHROMIUM
CPA000COMPOUND GLAZE
CUA000COPPER
CUB000COPPER ALLOY
DCA000DICHROMATE
ENA000ENAMEL
ENF000ENAMEL SEMIGLOSS
MSD000EPOXY
AUA000GOLD
FEA000IRON
LQA000LACQUER
PBA000LEAD
PBB000LEAD ALLOY
NLA000NICKEL
NLC000NICKEL ALLOY
XXB000OXIDE
XXF000OXIDE ALUMINUM
PNA000PAINT
PDA000PALLADIUM
PSA000PASSIVATE
PHA000PHOSPHATE
PHD000PHOSPHATE ZINC
PCA000PLASTIC
PCS000PLASTIC EPOXY
PCAF00PLASTIC EPOXY FORMALDEHYDE
PCB000PLASTIC POLYTETRAFLUOROETHYLENE
PTA000PLATINUM
PTB000PLATINUM ALLOY
CLC000PORCELAIN
RHA000RHODIUM
SLA000SILICON
AGA000SILVER
AGB000SILVER ALLOY
SRA000SOLDER
SNA000TIN
SNB000TIN ALLOY
VAA000VARNISH
WXA000WAX
ZNA000ZINC
ZNB000ZINC ALLOY
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3EDVTERMINALS
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AP33)Reply
GASSN STD
ACOMMERCIAL ITEM DESCRIPTION
KDEF STAN/SPEC
BFED SPEC
CFED STD
LGOVERNMENT STD/SPEC
NINTERNATIONAL STD/SPEC
FMFR REF
DMIL SPEC
EMIL STD
HNATIONAL SPEC
PNATIONAL STD
MNATIONAL STD/SPEC
Table 3
Reply Code (AP39)Reply
M10TH TREATMENT RESPONSE
N11TH TREATMENT RESPONSE
P12TH TREATMENT RESPONSE
Q13TH TREATMENT RESPONSE
R14TH TREATMENT RESPONSE
S15TH TREATMENT RESPONSE
B1ST TREATMENT RESPONSE
C2ND TREATMENT RESPONSE
D3RD TREATMENT RESPONSE
E4TH TREATMENT RESPONSE
F5TH TREATMENT RESPONSE
H6TH TREATMENT RESPONSE
J7TH TREATMENT RESPONSE
K8TH TREATMENT RESPONSE
L9TH TREATMENT RESPONSE
GALL TREATMENT RESPONSES
ASINGLE TREATMENT RESPONSE
ABGN*JBOARD OVERALL LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGNJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABGP*JBOARD OVERALL WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGPJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABGQ*JBOARD OVERALL HEIGHT
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGQJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABGR*JBOARD HEIGHT EXCLUDING TERMINALS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGRJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABGS*JBASE THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGSJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABGT*JBOARD THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGTJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CWLJ*JMAJOR DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWLJJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CWLL*JMINOR DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWLLJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CRTC*ATERMINAL STRIP DESIGN
THE SHAPE AND ARRANGEMENT OF THE TERMINAL/S/ AND MOUNTING FOOT /FEET/ AND/OR HOLE/S/.
Enter the alpha-numeric reply with a minimum of one character.
(CRTCAB1)
expandReference Notes
To determine the terminal design: a. Position the strip as follows: (1) If with mounting foot (feet), place foot down or to the right: (See Physical Drawing ID: AAR1262). (2) If without mounting foot (feet) but with mounting holes, not centrally located, place holes to the right: (See Physical Drawing ID: DQ01058). (3) If without mounting foot (feet) but with mounting hole centrally located, place lugs in up position: (See Physical Drawing ID: DQ01059). b. Select the applicable mounting foot or terminal position from Chart A (See Physical Drawing ID: AAR1263) for the lst (left) lug. c. Select the applicable terminal design from Chart B (See Physical Drawing ID: AAR1264) for the lst (left) lug. d. Combine the mounting/terminal position alphabetic symbol with the terminal design numeric symbol to describe one completed lug. e. Sequence the combination of symbols in Step d for each successive lug (left to right) to produce the terminal design for the whole terminal strip. Example: TERMINAL BOARD BODY STYLES: 1) APPROPRIATE CODING for Physical Drawing ID: AAR1203 is R3-R3-C1-R3-R3. 2) APPROPRIATE CODING for Physical Drawing ID: AAR1204 is T24-T24-T24-T24-H1. APPROPRIATE CODING for Physical Drawing ID: AAR1205 is K1-R3-R3-R3-R3-K1.
IF STYLE/REPLY CODE(s) CB OR CE WERE ENTERED FOR MRC CWLG, YOU MUST ANSWER MRC (ABCS and ABCU and ABCT)
IF STYLE/REPLY CODE(s) CC OR CD WERE ENTERED FOR MRC CWLG, YOU MUST ANSWER MRC (ABCS and CWKY and CXBN)
IF STYLE/REPLY CODE(s) CG WERE ENTERED FOR MRC CWLG, YOU MUST ANSWER MRC (ABCT)
IF STYLE/REPLY CODE(s) CH OR CJ WERE ENTERED FOR MRC CWLG, YOU MUST ANSWER MRC (CWJZ)
CWLG*DTERMINAL PATTERN ARRANGEMENT
THE ARRANGEMENT OF TERMINAL POSITIONS ON THE ITEM.
Enter the applicable reply code from the table below
(CWLGDCC*;CWLGDCE$$DCB*)
Table 1
Reply Code (AH86)Reply
CBMULTI-ROW
CCMULTI-ROW CIRCULAR
CDMULTI-ROW CIRCULAR WITH CENTER TERMINAL
CEMULTI-ROW STAGGERED
CFRANDOM
CGSINGLE ROW
CHSINGLE ROW CIRCULAR
CJSINGLE ROW CIRCULAR WITH CENTER TERMINAL
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
ABCS*ATERMINAL ROW QUANTITY
THE NUMBER OF TERMINAL ROWS OR TERMINAL PROVISIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ABCSA10*)
ABCU*JDISTANCE BETWEEN TERMINAL ROW CENTERS
THE DISTANCE BETWEEN THE TERMINAL ROW CENTERS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABCUJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CWJZ*JTERMINAL CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWJZJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CWKY*JINNER TERMINAL CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INNER TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWKYJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CXBN*JOUTER TERMINAL CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTER TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXBNJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABCT*JCENTER TO CENTER DISTANCE BETWEEN TERMINALS
THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABCTJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
IF STYLE/REPLY CODE(s) AAB OR BBW WERE ENTERED FOR MRC CWLN, YOU MUST ANSWER MRC (CQCW and CRZR)
IF STYLE/REPLY CODE(s) BBX WERE ENTERED FOR MRC CWLN, YOU MUST ANSWER MRC (CRNL and CSCS and CSCR and CQCZ)
IF STYLE/REPLY CODE(s) BBY OR BBZ WERE ENTERED FOR MRC CWLN, YOU MUST ANSWER MRC (CQCW and CRZR and CSCR and CQCZ)
IF STYLE/REPLY CODE(s) BCA WERE ENTERED FOR MRC CWLN, YOU MUST ANSWER MRC (CRNL and CSCS)
IF STYLE/REPLY CODE(s) BCB OR BCC WERE ENTERED FOR MRC CWLN, YOU MUST ANSWER MRC (CQCW and CRZR)
CWLN*DTERMINAL DESIGN
THE DESIGN OF THE TERMINAL.
Enter the applicable reply code from the table below
(CWLNDBBX*;CWLNDAAB$$DBBZ*)
Table 1
Reply Code (AH21)Reply
BSYCONNECTION SPRING CAGE
AABFEEDTHRU
BBWLATERAL FEEDTHRU
BBXLINKED NONFEEDTHRU
BBYLINKED OVEREDGE FEEDTHRU
BBZLINKED VERTICAL FEEDTHRU
BCANONFEEDTHRU
BCBOVEREDGE FEEDTHRU
BCCVERTICAL FEEDTHRU
CRNL*JNONFEEDTHRU TERMINAL TYPE
INDICATES THE TYPE OF NONFEEDTHRU TERMINAL FURNISHED WITH THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CRNL3AEEJAE2.0*;CRNL3AEEJAE2.0$JAE2.0*;CRNL3AEEJAE2.0$$JAE2.1*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AK17)Reply
ABFIRST
AEFOURTH
ACSECOND
AHSINGLE
ADTHIRD
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CSCS*JNONFEEDTHRU TERMINAL QUANTITY
THE NUMBER OF NONFEEDTHRU TERMINALS FURNISHED WITH THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CSCS3EDUJAH2*;CSCS3EDUJAH2$$JAH3*;CSCS3EDUJAH2$JAH2*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AK17)Reply
ABFIRST
AEFOURTH
ACSECOND
AHSINGLE
ADTHIRD
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CQCWJFEEDTHRU CONNECTION END TYPE
INDICATES THE TYPE OF CONDUCTOR CONNECTION FACILITY/IES/ FURNISHED ON EACH END OF A FEEDTHRU TERMINAL.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a alpha-numeric reply with a minimum of one character.
(CQCW3EDUJFF2.0*;CQCW3EDUJFF2.0$JFF2.0*;CQCW3EDUJFF2.0$$JFF2.1*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3EHDSECOND TRACER SINGLE CONDUCTOR
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AN95)Reply
BBOTH ENDS
FFIRST END
SSECOND END
Table 3
Reply Code (AN96)Reply
CFIRST COMBINATION
FFOURTH COMBINATION
DSECOND COMBINATION
BSINGLE COMBINATION
ETHIRD COMBINATION
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CRZR*JFEEDTHRU TERMINAL QUANTITY
THE NUMBER OF TERMINALS FURNISHED WITH THE ITEM WHICH HAVE CONDUCTOR CONNECTIONS ON EACH END.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CRZR3EDUJB2*;CRZR3EDUJB2$$JB3*;CRZR3EDUJB2$JB2*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AN96)Reply
CFIRST COMBINATION
FFOURTH COMBINATION
DSECOND COMBINATION
BSINGLE COMBINATION
ETHIRD COMBINATION
CSCR*JTERMINAL CONNECTING LINK TYPE
INDICATES THE TYPE OF TERMINAL CONNECTING LINK/S/ FURNISHED WITH THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CSCRJAH2*;CSCRJAH2$$JAH3*;CSCRJAH2$JAH2*)
Table 1
Reply Code (AK17)Reply
ABFIRST
ACSECOND
AHSINGLE
ADTHIRD
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CQCZ*JTERMINAL CONNECTING LINK QUANTITY
THE NUMBER OF TERMINAL CONNECTING LINKS FURNISHED WITH THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CQCZ3EDUJAC2*;CQCZ3EDUJAC2$$JAC3*;CQCZ3EDUJAC2$JAC2*)
Table 1
ISAC Field Indicator (5000)Location
3AEEOVERALL
3EDUBOARD
3HOULOCATION NOT OTHERWISE SPECIFIED
Table 2
Reply Code (AK17)Reply
ABFIRST
ACSECOND
AHSINGLE
ADTHIRD
BWGP*ASECTION QUANTITY
THE NUMBER OF SECTIONS INCLUDED.
Enter the numeric reply with a minimum of one digit.
(BWGPA10*)
ABCZ*ATERMINAL FACILITY QUANTITY PER SECTION
THE NUMBER OF TERMINAL FACILITIES PROVIDED IN EACH SECTION OF A SCORED TERMINAL BOARD WITHOUT TERMINALS.
Enter the numeric reply with a minimum of one digit.
(ABCZA10*)
ABDA*ATERMINAL QUANTITY PER SECTION
THE NUMBER OF TERMINALS FURNISHED IN EACH SECTION OF A SCORED TERMINAL BOARD.
Enter the numeric reply with a minimum of one digit.
(ABDAA10*)
ABDB*ATERMINAL FACILITY QUANTITY
THE NUMBER OF FACILITIES PROVIDED ON THE ITEM FOR THE INSTALLATION OF TERMINALS.
Enter the numeric reply with a minimum of one digit.
(ABDBA10*)
ABDH*ASINGLE FEEDTHRU RECEPTACLE QUANTITY
THE NUMBER OF SINGLE/UNCONNECTED/TAPER PIN FEEDTHRU RECEPTACLES PROVIDED IN THE TERMINAL BOARD.
Enter the numeric reply with a minimum of one digit.
(ABDHA10*)
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CSBQ*JCOMMON FEEDTHRU RECEPTACLE SET QUANTITY
THE NUMBER OF SETS OF COMMON TAPER PIN FEEDTHRU RECEPTACLES PROVIDED IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CSBQJB2*;CSBQJB2$$JB3*;CSBQJB2$JB2*)
Table 1
Reply Code (AN97)Reply
GFIFTH GROUP
CFIRST GROUP
FFOURTH GROUP
DSECOND GROUP
BSINGLE GROUP
ETHIRD GROUP
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
CQDC*JCOMMON FEEDTHRU RECEPTACLE QUANTITY PER SET
THE NUMBER OF TAPER PIN RECEPTACLES WHICH COMPRISES A SET OF COMMON FEEDTHRU RECEPTACLES IN AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQDCJG2*;CQDCJG2$$JG3*;CQDCJG2$JG2*)
Table 1
Reply Code (AN97)Reply
GFIFTH GROUP
CFIRST GROUP
FFOURTH GROUP
DSECOND GROUP
BSINGLE GROUP
ETHIRD GROUP
expandReference Notes
Refer to Reference Drawings for assitance in answering this MRC.
ABDU*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABDUJA2.0*;ABDUJA2.0$$JA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABDV*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABDVJA2.0*;ABDVJA2.0$$JA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABDW*JDISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO CENTER OF MOUNTING HOLE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABDWJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABDX*JDISTANCE FROM LEFT EDGE OF TERMINAL BOARD TO CENTER OF FIRST MOUNTING FACILITY
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABDXJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABDY*JDISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO BOTTOM EDGE OF MOUNTING FOOT
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABDYJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ABYY*JMOUNTING BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABYYJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAMA*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAMAJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAMB*JMOUNTING HOLE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING HOLE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAMBJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAQX*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQXJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
AAQW*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQWJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
IF STYLE/REPLY CODE(s) BR OR BS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and ADNE)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CWLF and ADNE) or (CWKZ and CTXF and ADNE) or (CWKZ and AKEM and ADNE)
IF STYLE/REPLY CODE(s) EM, MJ OR WW WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CTXF and CWLF and ADNE)
IF STYLE/REPLY CODE(s) NP WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CDTG and ADNE)
IF STYLE/REPLY CODE(s) SJ OR SK WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CTXF and ADNE) or (CWKZ and CWLF and ADNE)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE, NF, NJ OR UN WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CDTG and AKBM and ADNE) or (CWKZ and CDTG and AKEM and ADNE)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and CDTG and ADNE) or (CWKZ and CTXF and ADNE)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ and AKBM and CDTG and ADNE) or (CWKZ and AKEM and CDTG and ADNE)
IF STYLE/REPLY CODE(s) BA, BF OR BW WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CWKZ)
CDTD*DMOUNTING FACILITY THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A MOUNTING FACILITY DIAMETER.
Enter the applicable reply code from the table below
(CDTDDNE*;CDTDDNS$$DBW*)
Table 1
Reply Code (AH06)Reply
BABA
BFBRITISH STANDARD FINE (BSF)
BWBRITISH STANDARD WHITWORTH (BSW)
BSBSP.TR EXT
BRBSP.TR INT
SMISO M
SSISO S
EMM
MJMJ
NPNPT
SJSI
SKSI-M
UNUN
NCUNC
NEUNEF
NFUNF
NJUNIFIED NATIONAL FINE (UNJ)
JFUNIFIED NATIONAL JOINT FINE (UNJF)
JCUNJC
JEUNJEF
NMUNM
NSUNS
WWWHITWORTH
CWKZ*JMOUNTING FACILITY NOMINAL THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE NOMINAL THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWKZJA2.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
CDTG*AMOUNTING FACILITY THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE MOUNTING FACILITY PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CDTGAX1)
AKBM*AMOUNTING FACILITY THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED MOUNTING FACILITY.
Enter the alpha-numeric reply with a minimum of one character.
(AKBMAK0)
AKEM*JMOUNTING FACILITY THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE MOUNTING FACILITY.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AKEMJAM32.0/P50.0*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
ADNE*DMOUNTING THREAD DIRECTION
THE DIRECTION OF THE MOUNTING THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ADNEDAAL)
Table 1
Reply Code (AA38)Reply
AAGLEFT-HAND
AALRIGHT-HAND
CTXF*BMOUNTING FACILITY THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE MOUNTING FACILITY,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXFB2.0)
CWLF*JMOUNTING FACILITY THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A MOUNTING FACILITY THREAD.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CWLFJNTETEXT1234*)
Table 1
Reply Code (AN73)Reply
EXTEXTERNAL
NTEINTERNAL
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0)
AAPB*BDIELECTRIC WITHSTANDING VOLTAGE IN VOLTS
THE MAXIMUM VOLTAGE THE INSULATING MATERIALS OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAPBB2.0)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDABD*;CBBLDABL$$DABH*)
Table 1
Reply Code (AN47)Reply
ABCCABLE CLAMP
ABDCOMPONENT CLIPS
ABEFANNING HOLES
ABFFUNGUS PROOFING
ABGGROUNDING DEVICE
ABHMARKER STRIP
ABJMOISTURE PROOFING
ABKRADIO INTERFERENCE SHIELDING
FNYROHS DIRECTIVE COMPLIANCE
ABLSALT WATER RESISTANT
ABMTERMINAL COVERS
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
Table 1
Reply Code (AC28)Reply
ASPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
BSTANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
CDRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
Table 1
Reply Code (AN62)Reply
VFEDERAL MOTOR VEHICLE SAFETY STANDARD
FFLAMMABILITY STANDARD
SGOVERNMENT SPECIFICATION
TGOVERNMENT STANDARD
UINTERNATIONAL STD/SPEC
DMANUFACTURERS SOURCE CONTROL
RMANUFACTURERS SPECIFICATION
NMANUFACTURERS SPECIFICATION CONTROL
MMANUFACTURERS STANDARD
BNATIONAL STD/SPEC
APROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
PPROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
Table 1
Reply Code (AD08)Reply
ALALLOY
BEANNEALED
ANANNEX
APAPPENDIX
ACAPPLICABILITY CLASS
ARARRANGEMENT
ASASSEMBLY
ABASSORTMENT
BFBOND
BXBOX
CYCAPACITY
CACASE
CTCATEGORY
CFCIRCUMFERENCE
CLCLASS
CECODE
CRCOLOR
CCCOMBINATION CODE
CNCOMPONENT
CPCOMPOSITION
CMCOMPOUND
CDCONDITION
AVCONFIGURATION
CSCONSTRUCTION
BGCORE CONDITION
CBCUT OFF
AMDELAY CLASS
DEDESIGN
DGDESIGNATOR
DWDRAWING NUMBER
DUDUPLEX
EGEDGE
ENEND
FYFAMILY
FGFIGURE
AKFILE NUMBER
FNFINISH
FBFLAVOR
BHFLUX PERCENTAGE
FMFORM
FAFORMULA
AJGAGE STOCK NUMBER
GRGRADE
GAGRADUATION
AXGRANULES
AYGRIT
GBGROUND
GPGROUP
HAHEAVY DUTY
BAIMAGE COLOR
NSINSERT
TMITEM
KDKIND
KTKIT
LGLENGTH
LVLEVEL
LTLIMIT
MKMARK
AAMARKER
ADMASK APERTURE
MLMATERIAL
BBMAXIMUM DENSITY
TAMEDIUM TEMPER
MHMESH
MEMETHOD
BCMINIMUM DENSITY
MDMODEL
MTMOUNTING
AQNATURAL
AUNON-DELAY CLASS
NRNUMBER
BLOUTFIT NUMBER
PAPARAGRAPH
PTPART
PNPATTERN
PCPHYSICAL CONDITION
PSPIECE
PLPLAN
PRPOINT
PDPOLISHED
PBPRESSURE RATING
QAQUALITY
QBQUENCHED
RNRANGE
AERAPID
RTRATING
RFREFERENCE NUMBER
RAREGULAR DUTY
BJRMA FLUX
SJSALIENT CHARACTERISTICS
SCSCHEDULE
SBSECTION
SLSELECTION
BDSERIALIZED
SESERIES
SVSERVICE
SXSET
SASHADE
SHSHAPE
SGSHEET
SZSIZE
AGSLOW
TCSOFT TEMPER
SKSOURCE
PZSPECIES
SQSPECIFICATION SHEET
SDSPEED
AWSTANDARD
SRSTRAIGHT
STSTYLE
SSSUBCLASS
SFSUBFORM
SPSUBTYPE
BKSUPPORT
SNSURFACE CONDITION
SYSYMBOL
SMSYSTEM
TBTABLE
TNTANNAGE
TPTEMPER
TXTEXTURE
TKTHICKNESS
TTTREATMENT
TRTRIM
TYTYPE
YNUNIT
AZUNSERIALIZED
VAVARIETY
WTWEIGHT
WDWIDTH
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
Table 1
Reply Code (AD05)Reply
CYHARDENED
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
Table 1
Reply Code (AN58)Reply
AADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
Table 1
Reply Code (AN76)Reply
CCCUBIC CENTIMETERS
CNCUBIC INCHES
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDF)
Table 1
Reply Code (AD40)Reply
DDELICATE
BEXTREMELY FRAGILE
EMODERATELY DELICATE
FMODERATELY RUGGED
GRUGGED
CVERY DELICATE
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAZA000*;PRMTDPDA000$DRHA000*;PRMTDPDA000$$DRHA000*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000R2.0*;PMWTJRHA000R2.0$JRHA000R2.0*;PMWTJRHA000R2.0$$JRHA000R2.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
Table 2
Reply Code (AG14)Reply
EGRAINS, TROY
RGRAMS
FOUNCES, TROY
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
Table 1
Reply Code (MA01)Reply
AUA000GOLD
IRA000IRIDIUM
AZA000OSMIUM
PDA000PALLADIUM
PTA000PLATINUM
RHA000RHODIUM
RTA000RUTHENIUM
AGA000SILVER
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ011)
Table 1
Reply Code (HZ00)Reply
HAZ042ASBESTOS
HAZ008CADMIUM
HAZ011CHROMIUM
HAZ029LEAD
HAZ030MAGNESIUM ALLOY
HAZ052ZINC
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAM1)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)