A specific electrical element or set of electrical elements that are connected together to form a fixed arrangement and used as a substitute load for terminating an electrical circuit. A dummy load contains all the essential electrical characteristics necessary to terminate the circuit but does not function in the same manner as the load which it replaces. Examples are resistors used to replace antennas, batteries, loudspeakers, or the like. Includes single port terminations of twin lead, coaxial and waveguide transmission lines as low power terminations of a section of a transmission system in a specified manner. Includes dummy loads when arranged in a group or bank. Excludes:power absorbers. See also LOAD BANK, ELECTRICAL.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00335*)
IF STYLE/REPLY CODE(s) 10A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAQ)
IF STYLE/REPLY CODE(s) 11A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 12A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK and ADAQ and ADAU)
IF STYLE/REPLY CODE(s) 13A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK and ADAQ)
IF STYLE/REPLY CODE(s) 14A OR 15A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK and ABPM)
IF STYLE/REPLY CODE(s) 16A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ADAV)
IF STYLE/REPLY CODE(s) 17A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ABPM)
IF STYLE/REPLY CODE(s) 18A OR 21A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 19A OR 25A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK)
IF STYLE/REPLY CODE(s) 20A OR 22A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAT and ADAU and ADAV)
IF STYLE/REPLY CODE(s) 23A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 24A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK and ABPM)
IF STYLE/REPLY CODE(s) 26A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 27A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABPM and ADAV)
IF STYLE/REPLY CODE(s) 28A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK and ADAT and ADAU and ADAV)
IF STYLE/REPLY CODE(s) 29A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 1A, 2A, 4A OR 6A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAV)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABPM and ADAV)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 7A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK and ADAQ)
IF STYLE/REPLY CODE(s) 8A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKR and ABKW and ABMK and ADAQ and ADAU)
IF STYLE/REPLY CODE(s) 9A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAQ and ADAU)
IF STYLE/REPLY CODE(s) 30A, 31A, 32A, 33A, 34A OR 35A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK and ABKW)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL34A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAN1247 | 10A | RF CONNECTOR, SURFACE MOUNTED |
| AAN1248 | 11A | RF CONNECTOR, 4 HOLE OR CUSHION MOUNTED |
| AAN1249 | 12A | RF CONNECTOR, 4 HOLE MOUNTED |
| AAN1250 | 13A | RF CONNECTOR, 3 HOLE MOUNTED |
| AAN1251 | 14A | FLANGE, 4 HOLE MOUNTED |
| AAN1252 | 15A | FLANGE, 4 HOLE MOUNTED |
| AAN1253 | 16A | FLANGE, 4 HOLE MOUNTED |
| AAN1254 | 17A | FLANGE, WITHOUT FINS |
| AAN1255 | 18A | WAVEGUIDE MOUNTED |
| AAN1256 | 19A | WAVEGUIDE MOUNTED |
| AAN1240 | 1A | COAXIAL MOUNTED |
| AAN1257 | 20A | WAVEGUIDE MOUNTED |
| AAN1258 | 21A | WAVEGUIDE MOUNTED |
| AAN1259 | 22A | WAVEGUIDE MOUNTED |
| AAN1260 | 23A | WAVEGUIDE MOUNTED |
| AAN1261 | 24A | WAVEGUIDE MOUNTED |
| AAN1262 | 25A | WAVEGUIDE MOUNTED |
| AAN1263 | 26A | WAVEGUIDE MOUNTED |
| AAN1264 | 27A | WAVEGUIDE MOUNTED |
| AAN1265 | 28A | WAVEGUIDE MOUNTED |
| AAN1266 | 29A | WAVEGUIDE MOUNTED |
| AAN1241 | 2A | COAXIAL MOUNTED |
| AAN1267 | 30A | TERMINAL MOUNTED |
| AAN1268 | 31A | STUD MOUNTED |
| AAN1269 | 32A | ONE HOLE MOUNTED |
| AAN1270 | 33A | FLANGE TWO HOLE MOUNTED |
| AAN1271 | 34A | TWO HOLE MOUNTED |
| AAN1272 | 35A | STUD MOUNTED |
| AAN1242 | 3A | COAXIAL MOUNTED |
| AAN1238 | 4A | COAXIAL MOUNTED |
| AAN1239 | 5A | COAXIAL MOUNTED |
| AAN1243 | 6A | COAXIAL MOUNTED |
| AAN1244 | 7A | RF CONNECTOR, 4 HOLE MOUNTED |
| AAN1245 | 8A | RF CONNECTOR, 4 HOLE MOUNTED |
| AAN1246 | 9A | RF CONNECTOR, SURFACE MOUNTED |
AFGQJFREQUENCY RANGE RATING
THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFGQJMM32.0/P50.0*;AFGQJMM32.0/P50.0$$JM*)
| Table 1 |
| Reply Code (AC32) | Reply |
| G | GIGAHERTZ |
| E | HERTZ |
| K | KILOHERTZ |
| M | MEGAHERTZ |
AJDBJPOWER RATING
THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE DISSIPATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJDBJWD2.0*;AJDBJWD2.0$$JWD2.1*)
| Table 1 |
| Reply Code (AC33) | Reply |
| L | KILOWATTS |
| R | MEGAWATTS |
| W | WATTS |
| Table 2 |
| Reply Code (AF65) | Reply |
| D | AVERAGE |
| C | PEAK |
ACYWJIMPEDANCE RATING IN OHMS
THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE FLOW OF AN ALTERNATING CURRENT,EXPRESSED IN OHMS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYWJA2.0*;ACYWJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHTWBVOLTAGE STANDING WAVE RATIO
THE RATIO OF THE MAXIMUM TO THE MINIMUM AMPLITUDE OF PRESSURE /VOLTAGE/ MEASURED ALONG THE PATH OF THE WAVES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AHTWB2.0*;AHTWB2.0$$BM2.0*)
IF STYLE/REPLY CODE(s) AM WERE ENTERED FOR MRC AKRZ, YOU MUST ANSWER MRC (AXDC and AKSB)
IF STYLE/REPLY CODE(s) AL WERE ENTERED FOR MRC AKRZ, YOU MUST ANSWER MRC (AKSA)
IF STYLE/REPLY CODE(s) AK WERE ENTERED FOR MRC AKRZ, YOU MUST ANSWER MRC (AHUC and AHUD)
AKRZDTERMINATION TYPE
INDICATES THE TYPE OF FACILITY PROVIDED ON THE DEVICE FOR ATTACHING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(AKRZDAM*;AKRZDAL$DAB*;AKRZDAL$$DAB*)
| Table 1 |
| Reply Code (AE79) | Reply |
| ET | BINDING POST |
| AM | COAXIAL LINE FLANGE |
| AK | CONNECTION COAXIAL |
| EK | CONNECTOR |
| AB | CONNECTOR RECEPTACLE |
| AL | WAVEGUIDE FLANGE |
IF STYLE/REPLY CODE(s) AAW WERE ENTERED FOR MRC BFMF, YOU MUST ANSWER MRC (AWNJ and AWNL and AAXT and AKSC and AKSD)
IF STYLE/REPLY CODE(s) AAP WERE ENTERED FOR MRC BFMF, YOU MUST ANSWER MRC (AELA and AELB)
IF STYLE/REPLY CODE(s) AAQ WERE ENTERED FOR MRC BFMF, YOU MUST ANSWER MRC (AKSC)
BFMFDCOOLING METHOD
THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable reply code from the table below
(BFMFDAAP*;BFMFDAAT$DAAW*;BFMFDAAT$$DAAW*)
| Table 1 |
| Reply Code (AN05) | Reply |
| AAP | FORCED AIR |
| AAW | FORCED LIQUID |
| AAQ | LIQUID |
| AAT | SELF-COOLED |
ARNHDOPERATING POSITION
THE POSITION IN WHICH THE ITEM IS DESIGNED TO OPERATE.
Enter the applicable reply code from the table below
(ARNHDAC*;ARNHDAB$DAY*)
| Table 1 |
| Reply Code (AF63) | Reply |
| AY | ALL POSITIONS |
| AC | HORIZONTAL |
| AB | VERTICAL |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEHY*JAMBIENT TEMP AT FULL RATED POWER
THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHYJC2.0*;AEHYJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| K | KELVIN |
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQJAC2.0*;ABKQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAB2.0*;ABKRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAC2.0*;ABPMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAA2.0*;ADAQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAA2.0*;ADATJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKNK*JVOLTAGE STANDING WAVE RATIO FREQUENCY RANGE
THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE IN WHICH THE VOLTAGE STANDING WAVE RATIO IS SPECIFIED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AKNKJEM32.0/P50.0*;AKNKJEM32.0/P50.0$$JE*)
| Table 1 |
| Reply Code (AC32) | Reply |
| G | GIGAHERTZ |
| E | HERTZ |
| K | KILOHERTZ |
| M | MEGAHERTZ |
AXDC*DCOAXIAL LINE FLANGE TYPE
INDICATES THE TYPE OF COAXIAL LINE FLANGE PROVIDED.
Enter the applicable reply code from the table below
(AXDCDAJX)
| Table 1 |
| Reply Code (AK54) | Reply |
| AFG | RIGID |
| AJX | ROTATABLE |
AKSB*JCOAXIAL LINE FLANGE NOMINAL SIZE
THE DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE COAXIAL LINE FLANGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKSBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AKSA*AWAVEGUIDE FLANGE DESIGNATION
THE ALPHABETICAL CHARACTERS AND NUMERALS WHICH IDENTIFY THE SPECIFIC WAVEGUIDE FLANGE TYPE.
Enter the alpha-numeric reply with a minimum of one character.
(AKSAAL2)
AHUC*DCOAXIAL CONNECTOR SERIES DESIGNATION
A LETTER OR GROUP OF LETTERS USED TO DESIGNATE THE PARTICULAR COAXIAL CONNECTOR SERIES.
Enter the applicable reply code from the table below
(AHUCDAQ*;AHUCDCN$DAH*;AHUCDCN$$DAH*)
| Table 1 |
| Reply Code (AF42) | Reply |
| CW | 7MM |
| AU | APC-3.5 |
| BV | APC-7 |
| CN | APS |
| AH | BN |
| AB | BNC |
| BB | BRM |
| BG | BSM |
| AC | C |
| AD | HN |
| AE | LC |
| AQ | LN |
| AF | LT |
| AR | MB |
| AJ | N |
| BC | OSM |
| BD | OSSM |
| BE | PULSE |
| AV | QC |
| AK | QDL |
| AL | QDS |
| AX | QL |
| AW | QM |
| BA | SC |
| AY | SKL |
| AP | SM |
| BP | SMA |
| CU | SMB |
| BY | SMC |
| CY | SRM |
| CZ | TK |
| BL | TM |
| AG | TNC |
| AZ | TND |
| AM | TPS |
| BF | TWIN |
| AN | UHF |
AHUD*DCONNECTOR END DESIGN
THE DESIGN OF THE CONNECTOR END.
Enter the applicable reply code from the table below
(AHUDDA*;AHUDDB$$DC*)
| Table 1 |
| Reply Code (AB60) | Reply |
| B | FEMALE |
| A | MALE |
| C | NEUTER |
AWNJ*JCOOLANT CHAMBER PRESSURE
THE NOMINAL OUTWARD FORCE,PER UNIT OF AREA,OF THE COOLANT CHAMBER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWNJJC2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| C | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| G | POUNDS PER SQUARE INCH GAGE |
AWNL*JINPUT COOLANT TEMP
THE INPUT TEMPERATURE OF THE COOLANT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWNLJF2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AAXT*JCOOLING SYSTEM COOLANT FLOW RATE
THE AMOUNT OF COOLANT NECESSARY TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAXTJE2.0*)
| Table 1 |
| Reply Code (AC64) | Reply |
| A | CUBIC FEET PER MINUTE |
| C | CUBIC METERS PER MINUTE |
| M | GALLONS PER MINUTE |
| E | LITERS PER MINUTE |
IF YOU ANSWER MRC AELA, YOU MUST ANSWER MRC (AELC and AELD)
AELA*DBLOWER UNIT MOTOR CURRENT TYPE
INDICATES THE TYPE OF CURRENT FOR WHICH THE BLOWER UNIT MOTOR IS DESIGNED.
Enter the applicable reply code from the table below
(AELADB*;AELADC$$DB*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
AELB*BBLOWER UNIT MOTOR VOLTAGE RATING IN VOLTS
THE ELECTRICAL VOLTAGE VALUE FOR WHICH THE BLOWER UNIT MOTOR IS RATED,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AELBB2.0*;AELBB2.0$$BM2.0*)
AELC*BBLOWER UNIT MOTOR FREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE BLOWER UNIT MOTOR ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AELCB2.0*;AELCB2.0$$BM2.0*)
AELD*DBLOWER UNIT MOTOR INPUT PHASE
THE NUMBER OF ALTERNATING CURRENT PHASES OF THE BLOWER UNIT MOTOR INPUT.
Enter the applicable reply code from the table below
(AELDDC*;AELDDE$DB*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| E | SINGLE/THREE |
| C | THREE |
| B | TWO |
AKSC*DINTAKE CONNECTION THREAD LOCATION
THE LOCATION OF THE THREADS ON THE INTAKE CONNECTION.
Enter the applicable reply code from the table below
(AKSCDABY)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
AKSD*DDISCHARGE CONNECTION THREAD LOCATION
THE LOCATION OF THE THREADS ON A DISCHARGE CONNECTION.
Enter the applicable reply code from the table below
(AKSDDABX)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDB)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAN*;BBRGDAC$DAD*;BBRGDAC$$DAD*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAH*;BBRJDAB$$DAK*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AK | MAGNETIC |
| AH | RADIOACTIVE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPDA000*;PRMTDPTA000$DIRA000*;PRMTDPTA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPTA000F2.0*;PMWTJPTA000F2.0$JPTA000F2.0*;PMWTJPTA000F2.0$$JPTA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA0002.0*;PMLCJPDA0002.0$JPDA0002.0*;PMLCJPDA0002.0$$JPDA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAT0)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAB3)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDAK*;ENACDQH$$DQD*)
| Table 1 |
| Reply Code (EN02) | Reply |
| QD | HEXAVALENT CHROMIUM ALTERNATIVE |
| AK | NON-CADMIUM PRODUCT |
| QH | NON-LEAD ALTERNATIVE PRODUCTS |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CD | CUBIC DECIMETERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information