A thermally sensitive resistor whose primary function is to exhibit a change in electrical resistance with a change in body temperature. Item may be mounted in a probe or housing. For ballast tube type resistors, see RESISTOR (1), CURRENT REGULATING. Excludes:TRANSMITTER (1), TEMPERATURE, ELECTRICAL RESISTANCE and TEMPERATURE ELEMENT, RESISTANCE METEOROLOGICAL.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00309*)
CQWDJZERO POWER RESISTANCE
THE DC RESISTANCE VALUE MEASURED WITH A POWER DISSIPATION LOW ENOUGH THAT ANY FURTHER DECREASE IN POWER WILL RESULT IN NOT MORE THAN 0.1 PERCENT CHANGE IN RESISTANCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQWDJMZ2.0*)
| Table 1 |
| Reply Code (AN86) | Reply |
| GZ | GIGOHMS |
| KZ | KILOHMS |
| MZ | MEGOHMS |
| ZZ | OHMS |
CRQJFZERO POWER RESISTANCE TOLERANCE IN PERCENT AT REFERENCE TEMP
THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED ZERO POWER RESISTANCE,EXPRESSED IN PERCENT AT REFERENCE TEMPERATURE.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(CRQJFM2.0/P4.7*)
AKNADINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAB*;AKNADAC$DAD*;AKNADAC$$DAD*)
| Table 1 |
| Reply Code (AG85) | Reply |
| AC | ENCAPSULATED |
| AN | ENCASED |
| AD | HERMETICALLY SEALED |
| AB | UNINCLOSED |
AARGDRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDE*;AARGDN$DE*)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR)
IF STYLE/REPLY CODE(s) 3, 4, 5 OR 6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAQ)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ADAQ and ASDB)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ASDB)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 10 OR 11 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ABKW and ADAU and ADAT)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAU and ADAT)
IF STYLE/REPLY CODE(s) 13 OR 14 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAV)
IF STYLE/REPLY CODE(s) 15 OR 16 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAR)
IF STYLE/REPLY CODE(s) 17 OR 18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAT)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAU and ADAT)
IF STYLE/REPLY CODE(s) 20 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAT and ADAR)
IF STYLE/REPLY CODE(s) 21 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
IF STYLE/REPLY CODE(s) 22 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAT)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADEM and ADAR)
IF STYLE/REPLY CODE(s) 24 OR 25 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and ADAR and ABHP and ADEM and ABKW)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAU)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 28 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAU)
IF STYLE/REPLY CODE(s) 29 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AEJH and ADAQ)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AEJH and AEJG and ADAQ and ASDB)
IF STYLE/REPLY CODE(s) 32 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AEJG and ADAQ and ADAR)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AEJH and AEJG)
IF STYLE/REPLY CODE(s) 34 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AEJH and ADAQ)
IF STYLE/REPLY CODE(s) 35, 36, 37, 38 OR 39 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AEJH and AEJG)
IF STYLE/REPLY CODE(s) 40 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAQ and AEJG and AEJH)
IF STYLE/REPLY CODE(s) 42 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAQ)
IF STYLE/REPLY CODE(s) 43 OR 44 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAT)
IF STYLE/REPLY CODE(s) 45 OR 46 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAR and ADAT and ABMK)
IF STYLE/REPLY CODE(s) 47 OR 48 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAU and ADAQ and ADAT)
IF STYLE/REPLY CODE(s) 49 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and ADAU and AEJG and ABHP and AEJH)
IF STYLE/REPLY CODE(s) 50 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AEJH and AEJG and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 51 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABMK and ADAQ and ADAU)
IF STYLE/REPLY CODE(s) 52 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAU and ADAT and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 53 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AEJH and AEJG and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 54 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and AEJH and AEJG and ABHP)
IF STYLE/REPLY CODE(s) 55 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AEJH and AEJG and ABKW and ADAR and ABHP)
IF STYLE/REPLY CODE(s) 56 OR 57 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 58 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABMK and AEJH and AEJG and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 59 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ADAQ and ABHP)
IF STYLE/REPLY CODE(s) 60 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ASDB and AEJH and AEJG and ABHP)
IF STYLE/REPLY CODE(s) 61 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ADAQ)
IF STYLE/REPLY CODE(s) 62 OR 63 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAT and ADAQ and ADAU)
IF STYLE/REPLY CODE(s) 41 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEJH)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL9)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAM1463 | 1 | BEAD |
| AAM1472 | 10 | BEAD IN BOLOMETER MOUNTING |
| AAM1473 | 11 | BEAD IN CAN |
| AAM1474 | 12 | BEAD IN CAN |
| AAM1475 | 13 | PLAIN ROD |
| AAM1476 | 14 | PLAIN ROD |
| AAM1477 | 15 | ROD |
| AAM1478 | 16 | ROD |
| AAM1479 | 17 | PLAIN DISK |
| AAM1480 | 18 | DISK |
| AAM1481 | 19 | SQUARE OR RECTANGULAR WAFER |
| AAM1464 | 2 | BEAD |
| AAM1482 | 20 | DISK |
| AAM1483 | 21 | DISK ON SURFACE PLATE |
| AAM1484 | 22 | SPHERICAL |
| AAM1485 | 23 | PLAIN WASHER |
| AAM1486 | 24 | WASHER ASSY THROUGH HOLE MOUNT |
| AAM1487 | 25 | WASHER ASSY/SINGLE END |
| AAM1488 | 26 | DISK, PROBE |
| AAM1489 | 27 | PROBE, SURFACE MOUNTING |
| AAM1490 | 28 | DISK, PROBE |
| AAM1491 | 29 | PROBE, SURFACE MOUNTING |
| AAM1465 | 3 | SEALED OR COATED BEAD |
| AAM1492 | 30 | PROBE, FLANGE MOUNTING |
| AAM1493 | 31 | PROBE |
| AAM1494 | 32 | PROBE |
| AAM1495 | 33 | PROBE |
| AAM1496 | 34 | PROBE |
| AAM1497 | 35 | PROBE |
| AAM1498 | 36 | PROBE |
| AAM1499 | 37 | PROBE |
| AAM1500 | 38 | PROBE |
| AAM1501 | 39 | PROBE |
| AAM1466 | 4 | SEALED OR COATED BEAD |
| AAM1502 | 40 | PROBE |
| AAM1503 | 41 | PROBE, SURFACE MOUNTING |
| AAM1504 | 42 | BEAD TYPE EVACUATED OR GAS FILLED ENVELOPE W/ HEATER |
| AAM1505 | 43 | DISK |
| AAM1506 | 44 | DISK |
| AAM1507 | 45 | DISK |
| AAM1508 | 46 | DISK |
| AAM1509 | 47 | WAFER |
| AAM1510 | 48 | WAFER |
| AAM1511 | 49 | PROBE |
| AAM1467 | 5 | BEAD TYPE EVACUATED OR GAS FILLED ENVELOPE |
| AAM1512 | 50 | PROBE |
| AAM1513 | 51 | RECTANGULAR ROD |
| AAM1514 | 52 | RECTANGULAR ROD |
| AAM1515 | 53 | PROBE |
| AAM1516 | 54 | PROBE |
| AAM1517 | 55 | PROBE W/FLANGE MOUNTING |
| AAM1518 | 56 | MAGNETIC HEAD |
| AAM1519 | 57 | RIVET MOUNTED |
| AAM1520 | 58 | PROBE BRACKET MOUNTED |
| AAM1521 | 59 | SCREW MOUNTED |
| AAM1468 | 6 | BEAD TYPE EVACUATED OR GAS FILLED ENVELOPE |
| AAM1522 | 60 | PROBE |
| AAM1523 | 61 | BEAD IN CAN |
| AAM1524 | 62 | CHIP |
| AAM1525 | 63 | DUAL INLINE |
| AAM1469 | 7 | BEAD IN STUD |
| AAM1470 | 8 | BEAD IN MACHINE SCREW |
| AAM1471 | 9 | BEAD IN CARTRIDGE |
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAH2*;TTQYJAAH2$$JAAH3*;TTQYJAAH2$JAAH2*)
| Table 1 |
| Reply Code (AN89) | Reply |
| AAD | BONDING PAD |
| ACN | CONNECTOR, PLUG |
| AAH | FERRULE |
| AJB | FLANGE WAVEGUIDE |
| AEC | KNIFE BLADE |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| AAR | RIBBON |
| ABQ | SCREW |
| AJC | SURFACE CONTACT |
| ABX | TAB W/SCREW |
| ABB | TAB, SOLDER LUG |
| ABC | THREADED HOLE |
| ABD | THREADED STUD |
| ACB | TURRET |
| ACM | WIRE HOOK |
| ACC | WIRE LEAD |
| ACD | WIRE LOOP |
Reference NotesReply Code AAD BONDING PAD not illustrated - applicable to chip thype resistors onlyFor reply FLANGE, use Reply Code AJB FLANGE WAVEGUIDE
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY*;CBBLDFNY$$DFNY*)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDAGA000*;SFTT3AEEDAGA000$DAUA000*;SFTT3AEEDAGA000$$DAUA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CFV | TERMINAL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| CUA000 | COPPER |
| AUA000 | GOLD |
| NLA000 | NICKEL |
| PTA000 | PLATINUM |
| AGA000 | SILVER |
| SRA000 | SOLDER |
| SNA000 | TIN |
AEHX*JMAXIMUM POWER DISSIPATION RATING
THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHXJC2.0*)
| Table 1 |
| Reply Code (AC33) | Reply |
| C | MICROWATTS |
| M | MILLIWATTS |
| W | WATTS |
AEHY*JAMBIENT TEMP AT FULL RATED POWER
THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHYJF2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AEHZ*JMAXIMUM OPERATING TEMP
THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO OPERATE FOR AN EXTENDED PERIOD OF TIME.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHZJF2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AEJA*BTHERMAL TIME CONSTANT IN SECONDS
THE TIME REQUIRED FOR THE TEMPERATURE OF AN ITEM TO CHANGE 63.2 PERCENT OF THE DIFFERENCE BETWEEN ITS INITIAL AND FINAL BODY TEMPERATURE WHEN SUBJECTED TO A TEMPERATURE CHANGE UNDER ZERO POWER CONDITIONS,EXPRESSED IN SECONDS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEJAB2.0)
AEJB*BPOWER DISSIPATION CONSTANT IN MILLIWATTS PER DEG CELSIUS
THE RATIO,AT A SPECIFIED AMBIENT TEMPERATURE,OF A CHANGE IN POWER DISSIPATION IN AN ITEM TO THE RESULTANT BODY TEMPERATURE CHANGE,EXPRESSED IN MILLIWATTS PER DEGREE CELSIUS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEJBB2.0)
AEJC*BZERO POWER TEMP COEFFICIENT OF RESISTANCE IN PERCENT PER DEG CELSIUS
THE RATIO OF THE RATE OF CHANGE OF RESISTANCE WITH TEMPERATURE TO THE RESISTANCE OF THE ITEM AT A SPECIFIED TEMPERATURE,EXPRESSED IN PERCENT PER DEGREE CELSIUS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEJCB2.0)
IF STYLE/REPLY CODE(s) C OR F WERE ENTERED FOR MRC AEJD, YOU MUST ANSWER MRC (AEJE and AEJF)
AEJD*JTEMP POINTS FOR RESISTANCE READINGS AT ZERO POWER
THE TEMPERATURE LEVELS AT WHICH RESISTANCE RATINGS HAVE BEEN ESTABLISHED,UNDER ZERO POWER CONDITION.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJD3AIOJF2.0*;AEJD3AIOJF2.0$JF2.0*;AEJD3AIOJF2.0$$JF2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AIG | FIRST RESISTANCE-TEMPERATURE POINT |
| 3AIH | SECOND RESISTANCE-TEMPERATURE POINT |
| 3AII | THIRD RESISTANCE-TEMPERATURE POINT |
| 3AIJ | FOURTH RESISTANCE-TEMPERATURE POINT |
| 3AIK | FIFTH RESISTANCE-TEMPERATURE POINT |
| 3AIL | SIXTH RESISTANCE-TEMPERATURE POINT |
| 3AIM | SEVENTH RESISTANCE-TEMPERATURE POINT |
| 3AIN | EIGHTH RESISTANCE-TEMPERATURE POINT |
| 3AIO | NINTH RESISTANCE-TEMPERATURE POINT |
| 3AIP | TENTH RESISTANCE-TEMPERATURE POINT |
| 3AIQ | ALL RESISTANCE-TEMPERATURE POINTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AEJE*JZERO POWER RESISTANCE AT SPECIFIED TEMP
THE RESISTANCE AT A SELECTED TEMPERATURE,UNDER ZERO POWER CONDITION.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJE3AIOJQ2.0*;AEJE3AIOJQ2.0$JQ2.0*;AEJE3AIOJQ2.0$$JQ2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AIG | FIRST RESISTANCE-TEMPERATURE POINT |
| 3AIH | SECOND RESISTANCE-TEMPERATURE POINT |
| 3AII | THIRD RESISTANCE-TEMPERATURE POINT |
| 3AIJ | FOURTH RESISTANCE-TEMPERATURE POINT |
| 3AIK | FIFTH RESISTANCE-TEMPERATURE POINT |
| 3AIL | SIXTH RESISTANCE-TEMPERATURE POINT |
| 3AIM | SEVENTH RESISTANCE-TEMPERATURE POINT |
| 3AIN | EIGHTH RESISTANCE-TEMPERATURE POINT |
| 3AIO | NINTH RESISTANCE-TEMPERATURE POINT |
| 3AIP | TENTH RESISTANCE-TEMPERATURE POINT |
| 3AIQ | ALL RESISTANCE-TEMPERATURE POINTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
AEJF*FRESISTANCE TOLERANCE AT A SPECIFIED TEMP IN PERCENT
THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM AT A SELECTED TEMPERATURE IN PERCENT.
Enter the applicable ISAC from the table below followed by a range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AEJF3AINFM2.0/P4.7*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AIG | FIRST RESISTANCE-TEMPERATURE POINT |
| 3AIH | SECOND RESISTANCE-TEMPERATURE POINT |
| 3AII | THIRD RESISTANCE-TEMPERATURE POINT |
| 3AIJ | FOURTH RESISTANCE-TEMPERATURE POINT |
| 3AIK | FIFTH RESISTANCE-TEMPERATURE POINT |
| 3AIL | SIXTH RESISTANCE-TEMPERATURE POINT |
| 3AIM | SEVENTH RESISTANCE-TEMPERATURE POINT |
| 3AIN | EIGHTH RESISTANCE-TEMPERATURE POINT |
| 3AIO | NINTH RESISTANCE-TEMPERATURE POINT |
| 3AIP | TENTH RESISTANCE-TEMPERATURE POINT |
| 3AIQ | ALL RESISTANCE-TEMPERATURE POINTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAB2.0*;ADAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAA2.0*;ADARJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAA2.0*;ADATJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADEM*JWASHER THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADEMJAB2.0*;ADEMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJG*JPROBE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROBE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJGJAA2.0*;AEJGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJH*JPROBE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJHJAB2.0*;AEJHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAC2.0*;ASDBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKEJ*DMOUNTING FACILITY SCREW THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE MOUNTING FACILITY.
Enter the applicable reply code from the table below
(AKEJDNJ)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| SM | ISO M |
| SS | ISO S |
| NP | NPT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
CRYY*JMOUNTING FACILITY NOMINAL SCREW THREAD DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRYYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CGGK*JMOUNTING THREAD QUANTITY
THE NUMBER OF MOUNTING THREADS ON THE ITEM MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,INCLUDING INCOMPLETE THREADS.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CGGKJC2.0*;CGGKJC2.0$JC2.1*)
| Table 1 |
| Reply Code (AB39) | Reply |
| C | PER INCH |
| J | PER MILLIMETER |
CTLJ*BMOUNTING THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE MOUNTING THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTLJB2.0)
CWMS*JMOUNTING THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A MOUNTING THREAD.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CWMSJEXT2.0*;CWMSJEXT2.0$$JEXT2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJAA2.0*;AASAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAC2.0*;AEBVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJNJAA2.0*;AEJNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQJAC2.0*;ABKQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAA2.0*;ABKRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAC2.0*;ABJTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBT*JTERMINAL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBTJAB2.0*;AEBTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
CTGT*BREFERENCE TEMP IN DEG CELSIUS
THE TEMPERATURE AT WHICH NOMINAL ZERO POWER RESISTANCE IS SPECIFIED,EXPRESSED IN DEGREES CELSIUS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTGTB2.0)
AEWK*JMAXIMUM CURRENT RATING
THE MAXIMUM CONTINUOUS CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWKJL2.0*)
| Table 1 |
| Reply Code (AC30) | Reply |
| A | AMPERES |
| U | MICROAMPERES |
| L | MILLIAMPERES |
AEEF*ACONNECTOR MANUFACTURER PART NUMBER
THE IDENTIFYING PART NUMBER ASSIGNED TO THE ELECTRICAL CONNECTOR RECEPTACLE.
Enter the alpha-numeric reply with a minimum of one character.
(AEEFAK0)
AEEE*ACONNECTOR MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ELECTRICAL CONNECTOR RECEPTACLE.
Enter the alpha-numeric reply with five character(s) exactly.
(AEEEAS5O8C)
AEWM*JHEATER RESISTANCE
THE OHMIC VALUE OF THE RESISTANCE OF THE HEATER ELEMENT TO THE FLOW OF DIRECT CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWMJQ2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
AEWN*FHEATER RESISTANCE TOLERANCE IN PERCENT
THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE FROM THE RATED VALUE OF THE HEATER ELEMENT,EXPRESSED IN PERCENT.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AEWNFM2.0/P4.7*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDRHA000$DAZA000*;PRMTDRHA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000R2.0*;PMWTJRHA000R2.0$JRHA000R2.0*;PMWTJRHA000R2.0$$JRHA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)