A fuse in which the element may or may not be enclosed.It is specifically designed to close an auxiliary circuit.When the fuse element is broken, it may provide a visual signal.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00250*)
IF STYLE/REPLY CODE(s) 1C WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABMK and ABHP and ABKW)
IF STYLE/REPLY CODE(s) 2C WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKW and ABMK and ABTD and AFWY)
IF STYLE/REPLY CODE(s) 3C WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKQ and ABKW and ABTD)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL3C)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1053 | 1C | MINIATURE GRASSHOPPER |
| AAQ1054 | 2C | GRASSHOPPER TYPE |
| AAQ1055 | 3C | RESETTABLE GRASSHOPPER TYPE |
AEBJBCONTINUOUS CURRENT RATING IN AMPS
THE MAXIMUM DIRECT CURRENT,OR ROOT MEAN SQUARE CURRENT AT RATED FREQUENCY,THAT AN ITEM WILL CARRY CONTINUOUSLY.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEBJB2.0)
AFXEJMAXIMUM VOLTAGE RATING IN VOLTS
THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE IN AN ALTERNATING CURRENT AND/OR DIRECT CURRENT CIRCUIT,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFXEJC2.0*;AFXEJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AE16) | Reply |
| B | AC |
| C | DC |
IF STYLE/REPLY CODE(s) C WERE ENTERED FOR MRC AFXF, YOU MUST ANSWER MRC (CQPB)
AFXFDCIRCUIT OVER-CURRENT INTERRUPTION TYPE
INDICATES THE TYPE OF OVER-CURRENT CONDITIONS THAT AN ITEM IS DESIGNED TO WITHSTAND INDICATED BY THE SPEED OF CIRCUIT INTERRUPTION.
Enter the applicable reply code from the table below
(AFXFDD)
| Table 1 |
| Reply Code (AE68) | Reply |
| D | DELAY TIME |
| B | NORMAL INSTANTANEOUS |
| C | TIME DELAY |
AFXHDINTERRUPTION INDICATOR METHOD
THE MEANS IN WHICH THE ITEM SIGNALS THE INTERRUPTION OF A CIRCUIT.
Enter the applicable reply code from the table below
(AFXHDAC)
| Table 1 |
| Reply Code (AE70) | Reply |
| AD | BODY-VISUAL OR ALARM |
| AF | CERAMIC SHELL BREAKS |
| AG | COLORED BEAD SNAPS UP |
| AH | DOT CHANGES COLOR |
| AE | GRASSHOPPER |
| AJ | HOLE BLOWN IN LABEL |
| AK | INTEGRAL NEON LAMP GLOWS |
| AW | NO VISUAL INDICATION |
| AA | OPAQUE BODY |
| AL | POWDER BLOWS OUT |
| AM | RED FLAG APPEARS IN SLOT IN FERRULE |
| AC | TERMINAL-VISUAL OR ALARM |
| AN | VAPOR BLOWS OUT |
| AB | VISIBLE ELEMENT |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQJAC2.0*;ABKQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWY*JTERMINAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TERMINAL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWYJAB2.0*;AFWYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQPB*JCIRCUIT OVER-CURRENT INTERRUPTION DELAY TIME IN SECONDS
THE TIME ELAPSING BEFORE CIRCUIT INTERRUPTION OF AN ITEM OPERATED AT A SPECIFIED PERCENT OF ITS NORMAL CURRENT RATING,EXPRESSED IN SECONDS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQPBJAH2.0*;CQPBJAH2.0$$JAH2.1*)
| Table 1 |
| Reply Code (AP37) | Reply |
| AC | 130 PCT OF CURRENT RATING |
| AD | 135 PCT OF CURRENT RATING |
| AE | 150 PCT OF CURRENT RATING |
| AH | 200 PCT OF CURRENT RATING |
| AJ | 210 PCT OF CURRENT RATING |
| AK | 250 PCT OF CURRENT RATING |
| AM | 300 PCT OF CURRENT RATING |
| AN | 328 PCT OF CURRENT RATING |
| AP | 400 PCT OF CURRENT RATING |
| AQ | 500 PCT OF CURRENT RATING |
| AR | 566 PCT OF CURRENT RATING |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3CEPDWDL000*;MATT3CEPDWDL000$DAL7075*;MATT3CEPDWDL000$$DAL7075*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ACL | CAP |
| 3CEP | CASE |
| 3CFV | TERMINAL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL7075 | ALUMINUM ALLOY 7075 |
| BEB000 | BERYLLIUM COPPER (USE CUB000) |
| BND000 | BRONZE |
| BNAAAA | BRONZE CAST |
| CLD000 | CERAMIC |
| CRA000 | CHROMIUM |
| CRB000 | CHROMIUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| FBA000 | FIBER |
| FG0000 | FIBERGLASS |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| RBR000 | HARD RUBBER |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| LRA000 | LEATHER |
| LRE000 | LEATHER ARTIFICIAL |
| MGB000 | MAGNESIUM ALLOY |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCJ000 | PLASTIC MELAMINE |
| PCCB00 | PLASTIC NYLON |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAK00 | PLASTIC SILICONE |
| PCBC00 | PLASTIC STYRENE |
| CLB000 | PORCELAIN |
| STA000 | STEEL |
| ST0302 | STEEL COMP 302 |
| ST0304 | STEEL COMP 304 |
| ST0316 | STEEL COMP 316 |
| STB000 | STEEL CORROSION RESISTING |
| AAA012 | THERMOPLASTIC |
| SNB000 | TIN |
| WDC000 | WOOD |
| WDL000 | WOOD MAHOGANY |
| WDR000 | WOOD OAK |
| WDE000 | WOOD WALNUT |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3CFVDPCG000*;SFTT3CFVDPCG000$DAGA000*;SFTT3CFVDPCG000$$DAGA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CFV | TERMINAL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| CUB000 | COPPER ALLOY |
| NLA000 | NICKEL |
| PCG000 | PLASTIC POLYCARBONATE |
| AGA000 | SILVER |
| SRA000 | SOLDER |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDE)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
BBRH*JINSPECTION FREQUENCY
THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.
(BBRHJMHAC2*;BBRHJMHAC2$$JMHAC3*)
| Table 1 |
| Reply Code (AH68) | Reply |
| DY | DAYS |
| MH | MONTHS |
| YR | YEARS |
| Table 2 |
| Reply Code (AM82) | Reply |
| AB | FIRST INSPECTION |
| AC | REINSPECTION |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRTA000*;PRMTDPDA000$DAZA000*;PRMTDPDA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000R2.0*;PMWTJAUA000R2.0$JAUA000R2.0*;PMWTJAUA000R2.0$$JAUA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRTA0002.0*;PMLCJRTA0002.0$JRTA0002.0*;PMLCJRTA0002.0$$JRTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ012*;HZRDDHAZ042$$DHAZ012*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ012 | COPPER |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information