A contact spring type electrical fitting of two or more conductors, which is arranged for the insertion of a PLUG,TELEPHONE. One conductor may be grounded. Does not include separable telephone jacks which are termed, JACK ASSEM BLY,TELEPHONE. Excludes:JACK,TIP.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED00124*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDPCA000*;MATT3AEEDPCA000$DRCB000*;MATT3AEEDPCA000$$DRCB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAS | CONTACT |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ACL | CAP |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3AEF | HANDLE |
| 3BDD | INSULATOR |
| 3CFU | FINGER |
| 3CFV | TERMINAL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0104 | COPPER ALLOY 511 |
| CU0148 | COPPER ALLOY 745 |
| GSA000 | GLASS |
| AUA000 | GOLD |
| AUB000 | GOLD ALLOY |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PDA000 | PALLADIUM |
| PCA000 | PLASTIC |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCE000 | PLASTIC ALKYD |
| PCG000 | PLASTIC DIALLYL PHTHALATE |
| PCJ000 | PLASTIC MELAMINE |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAS00 | PLASTIC POLYVINYLIDENE FLUORIDE |
| PTA000 | PLATINUM |
| RCE000 | RUBBER |
| RCJ000 | RUBBER POLYBUTADIENE |
| RC0020 | RUBBER POLYISOPRENE NATURAL CLASS NR |
| RCB000 | RUBBER SYNTHETIC |
| AGA000 | SILVER |
| AGF000 | SILVER ALLOY |
| SLF000 | STEATITE |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| ZNB000 | ZINC |
AFZKAJACK CONTACT ARRANGEMENT DESIGNATOR
A DESIGNATION OF THE DESCRIPTION OF THE RELATIVE POSITION OF THE CONTACTS IN RELATIONSHIP TO EACH OTHER AND TO THE BODY.
Enter the alpha-numeric reply with a minimum of one character.
(AFZKAN4)
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
CSCFDTERMINAL TYPE
INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the applicable reply code from the table below
(CSCFDABS*;CSCFDAHD$DACR*;CSCFDAHD$$DACR*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ABL | BINDING POST |
| AFL | CRIMP |
| AHD | EXTERNAL SETSCREW |
| ABS | EYELET W/TAB |
| AHE | INTERNAL SETSCREW |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| ABQ | SCREW |
| AAS | SOLDER STUD |
| AFK | SOLDER WELL |
| ABB | TAB, SOLDER LUG |
| ABD | THREADED STUD |
| AHF | THREADED STUD SOLDER CUP |
| ACB | TURRET |
| ACC | WIRE LEAD |
| AFM | WIRE WRAP |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AFXEJMAXIMUM VOLTAGE RATING IN VOLTS
THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE IN AN ALTERNATING CURRENT AND/OR DIRECT CURRENT CIRCUIT,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFXEJC2.0*;AFXEJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AE16) | Reply |
| B | AC |
| C | DC |
AMPSBCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0)
AALVDELECTRICAL INSULATION FEATURE
THE FEATURE CONSISTING OF SLEEVES,COVERING,CAPS,MOUNTING BUSHINGS AND THE LIKE,USED TO ELECTRICALLY INSULATE AN ITEM.
Enter the applicable reply code from the table below
(AALVDAAE)
| Table 1 |
| Reply Code (AA47) | Reply |
| AAP | INSULATED COMPLETELY |
| AAQ | INSULATED FROM PANEL |
| AAE | UNINSULATED |
IF STYLE/REPLY CODE(s) 1, 2 OR 3 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAT and ADAU and AFQJ)
IF STYLE/REPLY CODE(s) 4, 5, 6, 7, 8, 9 OR 18 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAV and AFQJ)
IF STYLE/REPLY CODE(s) 10 OR 13 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAT and ADAU and AFQJ and AFYB)
IF STYLE/REPLY CODE(s) 11 OR 26 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAP and ADAV)
IF STYLE/REPLY CODE(s) 12, 15, 16 OR 19 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAV and AFQJ)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAT and ADAU and AFQJ and AFYC)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAV and AFQJ and AFYE)
IF STYLE/REPLY CODE(s) 20 OR 21 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAV and ADAQ and ADAP and AFYE)
IF STYLE/REPLY CODE(s) 22 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAP)
IF STYLE/REPLY CODE(s) 24 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAP and ADAT)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAP and ADAT and ABTB) or (ABHP and ABKW and ADAP and ADAT and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 25 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAP and ADAT and AFYE and ABTB) or (ABHP and ABKW and ADAP and ADAT and AFYE and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 27, 28 OR 29 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAP and ADAQ and ADAV)
IF STYLE/REPLY CODE(s) 28A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAP and ADAQ and ADAT)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABPM and ADAP and AFYE and ABTB) or (ABHP and ABKW and ABPM and ADAP and AFYE and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABPM and ADAP and ADAQ and ADAV)
IF STYLE/REPLY CODE(s) 32 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ADAP and ADAQ and ADAT and ADAU and AFYC)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK and ADAP)
IF STYLE/REPLY CODE(s) 34 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAT and AEJN and AFYC and ABTB) or (ABHP and ABKW and ADAT and AEJN and AFYC and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ADAP and ADAT and AEJN and AFYC and AFYE and ABTB) or (ABHP and ABKW and ADAP and ADAT and AEJN and AFYC and AFYE and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 36 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABMK and ADAP and ADAQ and ADAU and AEJN and AFYE and ABTB) or (ABHP and ABMK and ADAP and ADAQ and ADAU and AEJN and AFYE and ABTD and ABVG)
IF STYLE/REPLY CODE(s) 37 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABJT and ABKW and ABMK and AEJN and AFYF)
IF STYLE/REPLY CODE(s) 38 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABJT and ABKW and ADAV)
IF STYLE/REPLY CODE(s) 39 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABJT and ABKW and ABMK and AEJN)
IF STYLE/REPLY CODE(s) 40 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAQ and ADAV)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL13)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAM1245 | 1 | RIGHT ANGLE |
| AAM1254 | 10 | DUAL PATCH CORD STRAIGHT HANDLE |
| AAM1255 | 11 | STRAIGHT W/O HANDLE |
| AAM1256 | 12 | IN-LINE STRAIGHT |
| AAM1257 | 13 | DUAL STRAIGHT EXTENSION |
| AAM1258 | 14 | DUAL ACCOMMODATED STRAIGHT EXTENSION |
| AAM1259 | 15 | IN-LINE STRAIGHT |
| AAM1260 | 16 | COAXIAL IN-LINE STRAIGHT |
| AAM1261 | 17 | COAXIAL IN-LINE STRAIGHT HANDLE |
| AAM1262 | 18 | IN-LINE STRAIGHT HANDLE |
| AAM1263 | 19 | IN-LINE STRAIGHT HANDLE |
| AAM1246 | 2 | RIGHT ANGLE METER |
| AAM1264 | 20 | PRESS FIT MOUNTED |
| AAM1265 | 21 | RIVET MOUNTED |
| AAM1266 | 22 | SCREW MOUNTED |
| AAM1267 | 23 | THREADED BUSHING MOUNTED LONG FRAME |
| AAM1268 | 24 | THREADED BUSHING MOUNTED LONG FRAME |
| AAM1269 | 25 | BUSHING MOUNTED LONG FRAME |
| AAM1270 | 26 | THREADED BUSHING MOUNTED |
| AAM1271 | 27 | THREADED BUSHING MOUNTED |
| AAM1272 | 28 | THREADED BUSHING MOUNTED |
| DQ00129 | 28A | THREADED BUSHING MOUNTED |
| AAM1273 | 29 | THREADED BUSHING MOUNTED THICK PANEL |
| AAM1247 | 3 | RIGHT ANGLE SPLIT HANDLE |
| AAM1274 | 30 | COAXIAL HOLE OR SLOT MOUNTED |
| AAM1275 | 31 | THREADED BUSHING MOUNTED HERMETICALLY SEALED |
| AAM1276 | 32 | DUAL THREADED BUSHING MOUNTED |
| AAM1277 | 33 | RIGHT ANGLE THREADED BUSHING MOUNTED SHORT FRAME |
| AAM1278 | 34 | COAXIAL BRACKET MOUNTED |
| AAM1279 | 35 | DUAL HOLE OR SLOT MOUNTED |
| AAM1280 | 36 | DUAL COAXIAL HOLE OR SLOT MOUNTED |
| AAM1281 | 37 | TERMINAL MOUNTED |
| AAM1282 | 38 | TERMINAL MOUNTED |
| AAM1283 | 39 | TERMINAL MOUNTED |
| AAM1248 | 4 | STRAIGHT HANDLE |
| AAM1284 | 40 | PRESS FIT |
| AAM1249 | 5 | STRAIGHT HANDLE |
| AAM1250 | 6 | STRAIGHT W/TERMINATION SCREW THROUGH HANDLE |
| AAM1251 | 7 | STRAIGHT HANDLE |
| AAM1252 | 8 | STRAIGHT HANDLE W/CHUCK |
| AAM1253 | 9 | STRAIGHT W/O HANDLE |
IF YOU ANSWER MRC AFXS, YOU MUST ANSWER MRC (AFXY and AFXZ)
AFXSDACCOMMODATED FINGER TYPE
INDICATES THE TYPE OF FINGER/S/ ACCOMMODATED BY THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AFXS3CFPDBJ*;AFXS3CFPDBJ$DAW*;AFXS3CFPDBJ$$DAW*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CFO | ALL FINGERS |
| 3CFP | SINGLE FINGER |
| 3CFQ | FIRST FINGER |
| 3CFR | SECOND FINGER |
| 3CFS | THIRD FINGER |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AE71) | Reply |
| AB | BANANA CROSS CUT |
| AA | BANANA SPRING |
| AG | FOUR CONDUCTOR, CYLINDRICAL TIP |
| AQ | FOUR CONDUCTOR, JUMBO SPHERICAL TIP |
| BE | FOUR CONDUCTORS |
| BN | HELICALLY SLOTTED |
| AD | NEEDLE POINT |
| AW | NONCONDUCTIVE, CONE TIP |
| AS | NONCONDUCTIVE, ROUND TIP |
| BA | NONCONDUCTIVE, SLENDER SPHERICAL TIP |
| AY | NONCONDUCTIVE, TURRET TIP |
| AU | NONCONDUCTIVE, UNNOTCHED TIP |
| BF | SINGLE CONDUCTOR |
| AX | SINGLE CONDUCTOR, CONE TIP |
| AT | SINGLE CONDUCTOR, ROUND TIP |
| BB | SINGLE CONDUCTOR, SLENDER SPHERICAL TIP |
| AZ | SINGLE CONDUCTOR, TURRET TIP |
| AV | SINGLE CONDUCTOR, UNNOTCHED TIP |
| BG | SIX CONDUCTOR, CYLINDRICAL TIP |
| AC | SPLIT END |
| BH | SPLIT W/TENSIONER |
| BJ | STRAIGHT SLOTTED W/TENSIONER |
| AF | TEST PROD |
| AE | TEST PROD STEPPED |
| AP | THREE CONDUCTOR, CONE TIP |
| AR | THREE CONDUCTOR, SLENDER SPHERICAL TIP |
| BK | THREE CONDUCTOR, UNNOTCHED TIP |
| BL | THREE CONDUCTORS |
| AN | TWO CONDUCTOR, NOTCHED TURRET TIP |
| AM | TWO CONDUCTOR, ROUND TIP |
| AL | TWO CONDUCTOR, SLENDER ROUND TIP |
| AJ | TWO CONDUCTOR, SPHERICAL FLATTED TIP |
| AH | TWO CONDUCTOR, TURRET TIP |
| AK | TWO CONDUCTOR, UNNOTCHED TIP |
| BM | TWO CONDUCTORS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AFXZ*JFINGER ACCOMMODATION LENGTH
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFXZ3CFPJLB2.0*;AFXZ3CFPJLB2.0$JLB2.0*;AFXZ3CFPJLB2.0$$JLB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CFO | ALL FINGERS |
| 3CFP | SINGLE FINGER |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
AFXY*JFINGER ACCOMMODATION DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE FINGER, AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFXY3CFPJAB2.0*;AFXY3CFPJAB2.0$JAB2.0*;AFXY3CFPJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CFO | ALL FINGERS |
| 3CFP | SINGLE FINGER |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAA2.0*;ABPMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAA2.0*;ABTBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAA2.0*;ABTDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAA2.0*;ABVGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAP*JMOUNTING BUSHING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAPJAA2.0*;ADAPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAC2.0*;ADAQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAC2.0*;ADATJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJNJAC2.0*;AEJNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFQJ*JCABLE ENTRANCE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE ENTRANCE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFQJJAC2.0*;AFQJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYB*JCENTER TO CENTER DISTANCE BETWEEN FINGERS
THE CENTER TO CENTER DISTANCE BETWEEN THE FINGERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYBJAC2.0*;AFYBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYC*JCENTER TO CENTER DISTANCE BETWEEN FINGER ACCOMMODATIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYCJAC2.0*;AFYCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYE*JMOUNTING BUSHING DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYEJAA2.0*;AFYEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYF*JMOUNTING LEG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYFJAA2.0*;AFYFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXHR*JMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJACQ2*;AXHRJACQ2$$JACQ3*;AXHRJACQ2$JACQ2*)
| Table 1 |
| Reply Code (AM39) | Reply |
| ABD | BUSHING |
| ABY | SLOT |
| ACD | TERMINAL |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| ACQ | UNTHREADED HOLE |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CQQR and AAJF) or (CQJX and CTTC and AAJF) or (CQJX and AAJE and AAJF)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC and AAJE) or (CQJX and CQQR and AAJE)
IF STYLE/REPLY CODE(s) NP WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJF)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD and AAJF)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and AAJF)
IF STYLE/REPLY CODE(s) JS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and AAJE) or (CQJX and CMLP and AAJE)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJF) or (CQJX and CQQR and AAJF)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJE)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDSM*;THSDDNC$$DJF*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| NP | NPT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAR1)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJEXT2.0*;CTTCJEXT2.0$$JEXT2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAK5)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0*;CQQRB2.0$$BM2.0*)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*;AAJEJAM32.0/P50.0$$JA*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG*;AAJFDAAL$$DAAG*)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ABRR*JKEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRRJAA2.0*;ABRRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRV*JKEYWAY DEPTH
A MEASUREMENT FROM THE TOP SURFACE TO THE BOTTOM OF THE KEYWAY GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRVJAA2.0*;ABRVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYM*JBUSHING THRU-HOLE ACCOMMODATION DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYMJAA2.0*;AFYMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYP*JBUSHING THRU-HOLE ACCOMMODATION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYPJAA2.0*;AFYPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYQ*JBUSHING THRU-HOLE ACCOMMODATION WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYQJAC2.0*;AFYQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYR*JCENTER TO CENTER DISTANCE BETWEEN BUSHING THRU-HOLE ACCOMMODATIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYRJAC2.0*;AFYRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AATDCRA000*;SFTT3AATDCRA000$DANA000*;SFTT3AATDCRA000$$DANA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAS | CONTACT |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ACL | CAP |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3BDD | INSULATOR |
| 3CFU | FINGER |
| 3CFV | TERMINAL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| AUA000 | GOLD |
| PBA000 | LEAD |
| NLA000 | NICKEL |
| NLC000 | NICKEL ALLOY |
| NLB000 | NICKEL SILVER |
| PDA000 | PALLADIUM |
| PSA000 | PASSIVATE |
| AGA000 | SILVER |
| SRA000 | SOLDER |
| SNA000 | TIN |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDBC)
| Table 1 |
| Reply Code (AM81) | Reply |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AY | GENERAL PURPOSE HEATED WAREHOUSE |
| AZ | GENERAL PURPOSE UNHEATED WAREHOUSE |
| BC | HEATED-DEHUMIDIFIED |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAGA000*;PRMTDRHA000$DRTA000*;PRMTDRHA000$$DRTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000F2.0*;PMWTJRTA000F2.0$$JRTA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$JAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ029*;HZRDDHAZ008$$DHAZ052*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ008 | CADMIUM |
| HAZ029 | LEAD |
| HAZ052 | ZINC |
IF STYLE/REPLY CODE(s) BFP WERE ENTERED FOR MRC CXCJ, YOU MUST ANSWER MRC (AFYM)
IF STYLE/REPLY CODE(s) FTB OR FTC WERE ENTERED FOR MRC CXCJ, YOU MUST ANSWER MRC (AFYQ and AFYP)
IF STYLE/REPLY CODE(s) CLD WERE ENTERED FOR MRC CXCJ, YOU MUST ANSWER MRC (AFYM and AFYR)
CXCJ*DBUSHING ACCOMMODATION HOLE SHAPE
THE PHYSICAL CONFIGURATION OF THE HOLE DESIGNED TO ACCOMMODATE A BUSHING.
Enter the applicable reply code from the table below
(CXCJDFTC*;CXCJDBFP$DFTB*;CXCJDBFP$$DFTB*)
| Table 1 |
| Reply Code (AK54) | Reply |
| CLD | DOUBLE ROUND PLAIN |
| BFP | ROUND |
| FTB | ROUND W/DOUBLE FLAT |
| FTC | ROUND W/FLAT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)